DeWalt DWFP12658 instruction manual Assembly, Operation, Trigger, AIR Fitting, Preparing the Tool

Page 7

ASSEMBLY

WARNING: Disconnect air line from tool, engage trigger lock and remove fasteners from magazine before making adjustments or personal injury may result.

TRIGGER

WARNING: Keep fingers AWAY from the trigger when not driving fasteners to avoid accidental actuation. Never carry a tool with finger on the trigger. In bump action mode (contact actuation mode), the tool will drive a fastener if the contact trip is bumped while the trigger is depressed.

The DWFP12658 is equipped with a selectable trigger. This trigger allows the operator to select either single sequential action trigger mode or bump action trigger mode. In accordance with the ANSI Standard SNT-101-2002, the trigger is assembled in the single sequential action trigger mode. To change the trigger mode, see Actuating Tool instructions in the Operation section of the manual. The selectable trigger also has a trigger lock button to keep the trigger locked at all times when the tool is not in use.

AIR FITTING

The tool is equipped with a 1/4" (6.4 mm) male quick connector coupling. A 3/8" (9.5 mm) male quick connector coupling is available from DeWALT and may be used when a 1/4" (6.4 mm) supply line is not available.

NOTE: A 3/8" (9.5 mm) supply line (and fittings) are required for maximum tool performance.

WARNING: Always use couplings that relieve all pressure from the tool when it is disconnected from the power supply. Always use hose connectors that shut off air supply from compressor when the tool is disconnected.

To install an air fitting

1.Wrap the male end of the fitting with thread seal tape prior to assembly to eliminate air leaks.

2.To install a 1/4" (6.4 mm) fitting: screw it directly into the air inlet and tighten firmly.

NOTE: If an adapter is in the air inlet, remove it prior to inserting the fitting.

3.To install a 3/8" (9.5 mm) fitting: screw the fitting into the 3/8" (9.5 mm) adapter and then into the air inlet of the tool and tighten firmly.

OPERATION

PREPARING THE TOOL

WARNING: Read the section titled Important Safety Instructions for Pneumatic Tools at the beginning of this manual. Always wear eye and ear protection when operating this tool. Keep the nailer pointed away from yourself and others. For safe operation, complete the following procedures and checks before each use of the nailer.

NOTICE: To reduce the risk of damage to the tool, only use DeWALT pneumatic tool oil or a non-detergent SAE 20 weight oil. Oil with additives or detergent will damage tool parts.

1.Before you use the nailer, be sure that the compressor tanks have been properly drained.

2.Lubricate tool:

7 - ENG

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide D’UTILISATION Manual DE Instrucciones DWFP12658Definitions Safety Guidelines Important Safety Instructions For Pneumatic ToolsCompressor rated at over 200 psi. The tool operating Fig. E Fig. K Sequential Action Trigger Mode Bump or Contact Actuation Trigger ModeTo Avoid Double Fires Tool Parts Nail SpecificationsAIR Fitting AssemblyOperation TriggerPlatform Position Nail Length Loading the Tool FIGTo operate the tool in Single sequential actuation Mode Single Sequential actuation trigger modeActuating Tool Adjusting Depth FIG Clearing a Jammed Nail Shingle GuideCold Weather Operation Cleaning Repairs MaintenanceAccessories Daily Maintenance ChartThree Year Limited Warranty Tool Specifications Troubleshooting GuideSymptom Problems Solutions Compressor Connected Tools Number ’outil actionné pourrait projeter des débris, de la Mesures DE Sécurité DéfinitionsNe jamais modifier ni altérer l’outil. fig Fig. J Mode DE Détente Actionnée PAR Coup OU PAR Contact Pour Éviter LES Doubles Déclenchements Mode DE Détente À Action SéquentielleSpécifications Relatives AUX Clous Pièces DE L’OUTILRaccord D’AIR AssemblageFonctionnement DétenteChargement DE L’OUTIL FIG Position de la plateforme Longueur du clou Actionnement DE L’OUTILFonctionnement Intermittent de l’outil Mode de déclenchement séquentiel simple de la gâchette FigMode de déclenchement sur contact par gâchette Activation du mode déclenchementGUIDE-BARDEAU Réglage DE LA Profondeur FIGDégagement DES Clous Coincés Fonctionnement PAR Temps Chaud Solution Pourquoi CommentEntretien Fonctionnement PAR Temps FroidRéparations AccessoiresGarantie Limitée DE Trois ANS NettoyageGuide DE Dépannage Remplacement Gratuit DE LetiquietteFiche Technique DE L’OUTIL Symptôme Problème SolutionNombre D’OUTILS Raccordés AU Compresseur Regule la Presión De aire. Utilice presión de aire Pautas DE SEGURIDAD/DEFINICIONESCompatible Con las Indicaciones de la placa de la Revise la herramienta antes de usarla. No opere una No utilice gases envasados para esta herramientaFig. J Modo DE Gatillo DE Tope Modo DE Gatillo Secuencial Para Evitar LOS Dobles DisparosSiempre Especificaciones DE LOS Clavos Piezas DE LA HerramientaConector DE Aire EnsamblajeOperación GatilloCarga DE LA Herramienta FIG Posición de la plataforma Longitud del clavo Funcionamiento DE LA HerramientaCambiar el modo de disparo Modo de Disparo por contacto FigGuía DE Guijarros Ajuste DE LA Profundidad FIGExtracción DE UN Clavo Atascado Cuadro DE Mantenimiento Diario MantenimientoOperación EN Condiciones Climáticas Frías Operación EN Condiciones Climáticas CalurosasLimpieza AccesoriosReparaciones Reemplazo DE LAS Etiquetas DE Advertencia Garantía Limitada POR Tres AñosSíntoma Problema Solución Guía DE Detección DE ProblemasEspecificaciones DE LA Herramienta No se recomienda Compresseur Raccordés ’OUTILS NombreDewalt Industrial Tool Co East Joppa Road Towson, MD
Top Page Image Contents