Epson RS830 instruction manual Operation, Starting and Stopping

Page 18

4.While still holding the cuttinghead handle (L) Fig. 41 firmly, loosen the cuttinghead clamp knob, and slowly pull the cuttinghead (D) Fig. 41 toward the front of the track arm (E) until the travel stops. Turn the switch (H) “OFF”.

D E

H

L

5.Wait for the saw blade (M) Fig. 42 to stop, then return the cuttinghead (D) to the rear of the track arm (E). Note the saw kerf (N) Fig. 42 in the table boards.

D

Fig. 41

E

IMPORTANT: Raise the track arm (E) Fig. 42 before attempting to rotate it. Perform the procedure “CUTTING INTO THE TABLE BOARDS” for each separate angle cut.

M

N

Fig. 42

If, during operation, the saw has a tendency to tip over, slide, or walk on the supporting surface, secure the saw to the floor surface through the holes provided on the bottom of each leg.

operation

OPERATIONAL Controls and ADJUSTMENTS

Before using the saw, verify the following each and every time:

1.ALWAYS wear proper eye, hearing, and respiratory equipment.

2.Blade is tight.

3.Bevel angle and height lock knobs are tight.

4.If ripping, ensure fence lock lever is tight and fence is parallel to the blade.

5.The blade guard is properly attached and the anti-kick teeth are functioning.

6.ALWAYS inspect the guard and splitter for proper alignment operation and clearance with saw blade.

Failure to adhere to these common safety rules can greatly increase the likelihood of injury.

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

Before connecting the radial arm saw to the power source or operating the saw, always inspect the guard and splitter for proper operation alignment and clearance with saw blade. Personal injury may result.

If your saw makes an unfamiliar noise, or if it vibrates excessively, cease operating immmediately until the source has been located and the problem corrected.

STARTING AND STOPPING

Make sure that the switch is in the “OFF” position before plugging cord into outlet. Do not touch the plug’s metal prongs when unplugging or plugging in the cord.

The on/off switch (A) Fig. 43 is located at the front of the cuttinghead. To turn the saw “ON”, move the switch (A) up to the “ON” position. To turn the saw “OFF”, move the switch down to the “OFF” position.

18

Image 18

Contents RS830 Table of Contents Important Safety InstructionsGeneral SAFETY RULES Grounding InstructionsVolt Single Phase Operation Fig. CMinimum Gauge for Cord Sets Ampere RatingAdditional Specific Safety Rules SAW Blade Guard and Splitter How to avoid them and protect yourself from possible injuryFunctional Description KickbacksCarton Contents Unpacking and Cleaning Assembly Tools RequiredAssembly Time Estimate Attaching the Legs to the SAW Base Attaching the Wrench HookRemoving the Blade and Blade Guard from the SAW Table Supports Page Table Board Clamps and Table Boards Adjusting and Checking SAW Blade Travel Removing Heeling Adjusting IN/OUT RIP Scale Attaching the Blade and Blade GuardCutting Into the Table Boards Operation Starting and StoppingLocking the Switch in the OFF Position Guide to ControlsAdjusting the Ball Bearings Against the Track Adjusting the Tension on the Elevating Column Changing the Position of the Track ARM Clamping HandlePositive Stop Yoke Index Changing the Position of the Bevel Clamp HandleChanging the Position of the Yoke Clamp Handle Positive Stop Bevel IndexCROSS-CUTTING Adjusting the Splitter and ANTI-KICKBACK FingersUsing a Table Extension Auxiliary Table Board FacingCROSS-CUT Stop Miter CuttingAdjusting the Splitter and ANTI-KICKBACK Compound Miter CuttingRipping Failure to Start TroubleshootingKeep Machine Clean Lubrication & RUST PROTECTIONPush Stick Warranty ServiceAccessories Replacement Parts Service and RepairsFree warning label replacement LES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsRègles DE Sécurité Générales Conserver CES DirectivesOperation DE Phase DE Seul DE Volt Directives de sécurité importantesCalibre Minimum Pour Rallonge Règles Spécifiques Additionnelles De Sûreté Description Fonctionnelle AVANT-PROPOSContenus DE Boite Pièces DE LA Scie À Bras RadialPièces DE LA Planche DE Banc Désemballage ET Nettoyage Lestimation DE Temps Dassemblee AssemblageOutils Nécessaires Pour L’ASSEMBLEE Attacher LES Pattes AU Socle DE LA ScieEnlever LA Lame ET LE PROTÈGE-LAME DE LA Scie Supports DU BancInsérer quatre vis à tête ronde de 6,3 mm 1/4 po Brides Pour Planche DE Banc ET Planches DE Banc Ajuster ET Vérifier LA Course DE LA Lame Éliminer LE « Talonnement » Aligner LA Lame DE LA Scie Avec LE BancRégler L’ÉCHELLE DE Sciage À L’INTÉRIEUR/À L’EXTÉRIEUR Attacher LA Lame ET LE PROTÈGE-LAMECouper Dans LES Planches DU Banc Fonctionnement Démarrage ET Arrêt DE ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Guide des pièces Ajustement DES Roulements À Billes SUR LA Voie Ajuster LA Tension DE LA Colonne ÉlévatriceChanger LA Position DE LA Poignée DE Fixation DU Bras Changer LA Position DE LA Poignée DE Fixation DE BiseauIndex DE Biseau Butée Positive Changer LA Position DE LA Poignée DE Fixation DE LA FourcheIndex DE Fourche Butée Positive Ajustement DU Séparateur ET DU Doigt ANTI-EFFET DE RebondTronçonnage Revêtement Auxiliaire DES Planches DU BancUtiliser UNE Rallonge Découpe À Onglet Mixte Butée Pour LE TronçonnageDécoupe À Onglet Sciage EN LongSciage Vers L’EXTÉRIEUR Sciage Vers L’INTÉRIEURPoussoirs Poussoir Fabrication DUN PoussoirDepannage Entretien Pièces DE Rechange Entretien ET RéparationRemplacement Gratuit DE Létiquette Accessoiries GarantieInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESGuarde Estas Instrucciones Normas Generales DE Seguridad Conserve Estas InstruccionesInstrucciones de seguridad importantes Operación DE UNA Sola Fase CON 240 VoltiosCalibre Mínimo Para LOS Juegos DE Cables Normas Específicas Adicionales DE Seguridad Descripción Funcional PrologoProtector DE LA Hoja Y Hendedor Contenido DE Carton Piezas DE LA Sierra DE Brazo RadialPiezas DE LA Tabla DE Mesa Desempaquetado y LimpiEZA Para Ensamblar LAS Patas a LA Base DE LA Sierra Herramientas DE Ensamblaje RequeridasEstimación DEL Tiempo DE Ensamblaje Para Ensamblar EL Gancho DE LlavesPara Retirar LA Hoja Y EL Protector DE LA Hoja DE LA Sierra Soportes DE LA Mesa Page Abrazaderas DE LA Tabla DE Mesa Y LAS Tablas DE Mesa Para Eliminar LA Inclinación Angular Heeling Para QUE LA Hoja DE LA Sierra Cuadre CON LA Mesa ¡Desconecte la máquina de la fuente del poderPara Montar LA Hoja Y EL Protector DE LA Hoja Para Cortar Entro DE LAS Tablas DE Mesa Cada vez que use la sierra, verifique que OperaciónArrancando Y Deteniendo LA Sierra Fijando EL Interruptor EN LA Posicion DE ApagadoGuía sobre las piezas Las tuercas hexagonales D contra la base de la columna Para Ajustar LOS Cojinetes Contra EL RielPara Ajustar LA Tensión EN LA Columna DE Elevación Contra chaveta H hasta que se elimine toda la holgura dePara Cambiar LA Posición DEL Mango DE Sujeción de bisel Índice DE Tope Positivo DEL Bisel Cambiar configuraciones o realizar reparaciones. UnÍndice DEL Tope Positivo DE LA Horquilla Para Ajustar EL Separador Y EL Dedo AntiretrocesoEL USO DE UNA Extensión DE Mesa Corte TransversalEL Revestimiento Auxiliar DE LA Mesa Tope DE Corte TransversalCorte Longitudinal Corte DE IngletesCorte DE Ingletes Compuestos Nunca toque el extremo libre deCorte Longitudinal Externo Corte Longitudinal InternoVaras DE Empuje Construcción DE UNA Vara Para Empujar Localizacion DE Fallas Mantenimiento ServicioReemplazo Gratuito DE LAS Etiquetas DE Advertencia Accesorios Identificación DelproductoExcepciones Garantia Para Otras LocalidadesDelta Machinery Highway 45 North Jackson, TN 800