Epson RS830 instruction manual Volt Single Phase Operation, Fig. C

Page 4

240 VOLT SINGLE PHASE OPERATION

The 120/240 volt, dual-voltage motor supplied with your machine was shipped prepared for 120 volt operation. It can be converted for 240 volt operation.

Use the following instructions to convert your saw to 240 volts.

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

1.Remove the screw (A) Fig. D and remove the plastic cover (B).

2.Carefully slide the switch (C) Fig. E in the motor junction box to read 240 volts. Replace the plastic cover and screw that were removed in STEP 1.

3.You must also replace the 120 volt plug with a UL/CSA listed plug suitable for 240 volts and the rated current of the saw.

Either use a qualified electrician to do the conversion, or take the machine to an Authorized Delta Service Center. The machine must conform to the National Electric Code and all local codes and ordinances.

Use the 240 volt plug ONLY in an outlet that has the same configuration as the plug illustrated in Fig. C. DO NOT use an adapter with the 240 volt plug.

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

Fig. C

IS LONGEST OF THE 3 BLADES.

B

A

Fig. D

C

Fig. E

important safety instructions

1.TO REDUCE THE RISK OF KICKBACK AND OTHER INJURIES, KEEP GUARDS IN PLACE, and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from spindle before turning tool on. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to avoid tripping or placing arms, hands, and fingers in danger.

4

Image 4
Contents RS830 Table of Contents Important Safety InstructionsGeneral SAFETY RULES Grounding InstructionsVolt Single Phase Operation Fig. CMinimum Gauge for Cord Sets Ampere RatingAdditional Specific Safety Rules How to avoid them and protect yourself from possible injury Functional DescriptionSAW Blade Guard and Splitter KickbacksCarton Contents Assembly Tools Required Unpacking and CleaningAssembly Time Estimate Attaching the Wrench Hook Attaching the Legs to the SAW BaseRemoving the Blade and Blade Guard from the SAW Table Supports Page Table Board Clamps and Table Boards Adjusting and Checking SAW Blade Travel Removing Heeling Adjusting IN/OUT RIP Scale Attaching the Blade and Blade GuardCutting Into the Table Boards Operation Starting and StoppingLocking the Switch in the OFF Position Guide to ControlsAdjusting the Ball Bearings Against the Track Adjusting the Tension on the Elevating Column Changing the Position of the Track ARM Clamping HandleChanging the Position of the Bevel Clamp Handle Changing the Position of the Yoke Clamp HandlePositive Stop Yoke Index Positive Stop Bevel IndexAdjusting the Splitter and ANTI-KICKBACK Fingers Using a Table ExtensionCROSS-CUTTING Auxiliary Table Board FacingCROSS-CUT Stop Miter CuttingCompound Miter Cutting Adjusting the Splitter and ANTI-KICKBACKRipping Troubleshooting Keep Machine CleanFailure to Start Lubrication & RUST PROTECTIONPush Stick Service AccessoriesWarranty Replacement Parts Service and RepairsFree warning label replacement LES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsRègles DE Sécurité Générales Conserver CES DirectivesOperation DE Phase DE Seul DE Volt Directives de sécurité importantesCalibre Minimum Pour Rallonge Règles Spécifiques Additionnelles De Sûreté Description Fonctionnelle AVANT-PROPOSPièces DE LA Scie À Bras Radial Contenus DE BoitePièces DE LA Planche DE Banc Désemballage ET Nettoyage Assemblage Outils Nécessaires Pour L’ASSEMBLEELestimation DE Temps Dassemblee Attacher LES Pattes AU Socle DE LA ScieEnlever LA Lame ET LE PROTÈGE-LAME DE LA Scie Supports DU BancInsérer quatre vis à tête ronde de 6,3 mm 1/4 po Brides Pour Planche DE Banc ET Planches DE Banc Ajuster ET Vérifier LA Course DE LA Lame Éliminer LE « Talonnement » Aligner LA Lame DE LA Scie Avec LE BancRégler L’ÉCHELLE DE Sciage À L’INTÉRIEUR/À L’EXTÉRIEUR Attacher LA Lame ET LE PROTÈGE-LAMECouper Dans LES Planches DU Banc Démarrage ET Arrêt DE Scie FonctionnementVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Guide des pièces Ajustement DES Roulements À Billes SUR LA Voie Ajuster LA Tension DE LA Colonne ÉlévatriceChanger LA Position DE LA Poignée DE Fixation DU Bras Changer LA Position DE LA Poignée DE Fixation DE BiseauChanger LA Position DE LA Poignée DE Fixation DE LA Fourche Index DE Fourche Butée PositiveIndex DE Biseau Butée Positive Ajustement DU Séparateur ET DU Doigt ANTI-EFFET DE RebondRevêtement Auxiliaire DES Planches DU Banc TronçonnageUtiliser UNE Rallonge Butée Pour LE Tronçonnage Découpe À OngletDécoupe À Onglet Mixte Sciage EN LongSciage Vers L’INTÉRIEUR Sciage Vers L’EXTÉRIEURPoussoirs Poussoir Fabrication DUN PoussoirDepannage Entretien Pièces DE Rechange Entretien ET RéparationRemplacement Gratuit DE Létiquette Accessoiries GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesGuarde Estas Instrucciones Normas Generales DE Seguridad Conserve Estas InstruccionesInstrucciones de seguridad importantes Operación DE UNA Sola Fase CON 240 VoltiosCalibre Mínimo Para LOS Juegos DE Cables Normas Específicas Adicionales DE Seguridad Prologo Descripción FuncionalProtector DE LA Hoja Y Hendedor Piezas DE LA Sierra DE Brazo Radial Contenido DE CartonPiezas DE LA Tabla DE Mesa Desempaquetado y LimpiEZA Herramientas DE Ensamblaje Requeridas Estimación DEL Tiempo DE EnsamblajePara Ensamblar LAS Patas a LA Base DE LA Sierra Para Ensamblar EL Gancho DE LlavesPara Retirar LA Hoja Y EL Protector DE LA Hoja DE LA Sierra Soportes DE LA Mesa Page Abrazaderas DE LA Tabla DE Mesa Y LAS Tablas DE Mesa Para Eliminar LA Inclinación Angular Heeling Para QUE LA Hoja DE LA Sierra Cuadre CON LA Mesa ¡Desconecte la máquina de la fuente del poderPara Montar LA Hoja Y EL Protector DE LA Hoja Para Cortar Entro DE LAS Tablas DE Mesa Operación Arrancando Y Deteniendo LA SierraCada vez que use la sierra, verifique que Fijando EL Interruptor EN LA Posicion DE ApagadoGuía sobre las piezas Para Ajustar LOS Cojinetes Contra EL Riel Para Ajustar LA Tensión EN LA Columna DE ElevaciónLas tuercas hexagonales D contra la base de la columna Contra chaveta H hasta que se elimine toda la holgura dePara Cambiar LA Posición DEL Mango DE Sujeción de bisel Cambiar configuraciones o realizar reparaciones. Un Índice DEL Tope Positivo DE LA HorquillaÍndice DE Tope Positivo DEL Bisel Para Ajustar EL Separador Y EL Dedo AntiretrocesoCorte Transversal EL Revestimiento Auxiliar DE LA MesaEL USO DE UNA Extensión DE Mesa Tope DE Corte TransversalCorte DE Ingletes Corte DE Ingletes CompuestosCorte Longitudinal Nunca toque el extremo libre deCorte Longitudinal Interno Corte Longitudinal ExternoVaras DE Empuje Construcción DE UNA Vara Para Empujar Localizacion DE Fallas Mantenimiento ServicioReemplazo Gratuito DE LAS Etiquetas DE Advertencia Identificación Delproducto AccesoriosExcepciones Garantia Para Otras LocalidadesDelta Machinery Highway 45 North Jackson, TN 800