Epson RS830 Changing the Position of the Bevel Clamp Handle, Positive Stop Yoke Index

Page 22

CHANGING THE POSITION OF THE BEVEL CLAMP HANDLE

To reposition the bevel clamp handle:

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

1.Loosen the bevel clamp handle (A) Fig. 52, release the bevel index release knob (B), and turn the motor (C) to the vertical position.

NOTE: If the blade guard contacts the table surface, raise the track arm.

2.Loosen the bevel clamp handle (A) Fig. 52 several turns until the hex head of the screw (D) can be pushed out of hex-shaped recess in yoke.

3.Turn the screw (D) Fig. 52 one or two flats of the hex head in the direction the handle needs to be turned. Push it back into hex-shaped recess in yoke.

4.Tighten the bevel clamp handle (A) Fig. 52.

NOTE: The screw is left-hand thread - turn the clamp handle counter-clockwise to tighten.

D

C

B

A

Fig. 52

CHANGING THE POSITION OF THE YOKE CLAMP HANDLE

To reposition the yoke clamp handle (A) Fig. 53:

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

1 Remove retaining ring (B) Fig. 53.

2.Reposition yoke clamp handle (A) Fig. 53 on hex clamp nut.

3.Replace retaining ring (B) Fig. 53

a

b

Fig. 53

POSITIVE STOP YOKE INDEX

The yoke index lever (A) Fig. 54 activates a positive stop that positions the cuttinghead in the cross-cut or rip position. To rotate the cuttinghead, release the yoke clamp handle, press up or down on yoke index lever (A) to release the positive stop, and rotate the cuttinghead to either the #1 in-rip or #2 out-rip or #3 cross-cut positions. Release the yoke index lever (A) Fig. 53 and the cuttinghead will automatically index at each of the three positions.

POSITIVE STOP BEVEL INDEX

The bevel index knob (A) Fig. 55 provides a positive stop when positioning the saw blade at 0°, 45°, and 90° left, and 90° right on the bevel scale (C). To change the angle of the saw blade, loosen the bevel clamp handle (B), pull out bevel index knob (A), and tilt the saw blade and motor. For the 0°, 45°, and 90° left, and 90° right positions, release the bevel index knob (A) and the saw blade will index at each of these positions. Tighten the bevel clamp handle (B). For saw blade angles between positive stops, set the blade at the desired angle on bevel scale (C) and tighten the bevel clamp handle (B) Fig. 55.

A

Fig. 54

C

b

A

Fig. 55

22

Image 22
Contents RS830 Table of Contents Important Safety InstructionsGeneral SAFETY RULES Grounding InstructionsVolt Single Phase Operation Fig. CMinimum Gauge for Cord Sets Ampere RatingAdditional Specific Safety Rules SAW Blade Guard and Splitter How to avoid them and protect yourself from possible injuryFunctional Description KickbacksCarton Contents Assembly Tools Required Unpacking and CleaningAssembly Time Estimate Attaching the Wrench Hook Attaching the Legs to the SAW BaseRemoving the Blade and Blade Guard from the SAW Table Supports Page Table Board Clamps and Table Boards Adjusting and Checking SAW Blade Travel Removing Heeling Adjusting IN/OUT RIP Scale Attaching the Blade and Blade GuardCutting Into the Table Boards Operation Starting and StoppingLocking the Switch in the OFF Position Guide to ControlsAdjusting the Ball Bearings Against the Track Adjusting the Tension on the Elevating Column Changing the Position of the Track ARM Clamping HandlePositive Stop Yoke Index Changing the Position of the Bevel Clamp HandleChanging the Position of the Yoke Clamp Handle Positive Stop Bevel IndexCROSS-CUTTING Adjusting the Splitter and ANTI-KICKBACK FingersUsing a Table Extension Auxiliary Table Board FacingCROSS-CUT Stop Miter CuttingCompound Miter Cutting Adjusting the Splitter and ANTI-KICKBACKRipping Failure to Start TroubleshootingKeep Machine Clean Lubrication & RUST PROTECTIONPush Stick Warranty ServiceAccessories Replacement Parts Service and RepairsFree warning label replacement LES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsRègles DE Sécurité Générales Conserver CES DirectivesOperation DE Phase DE Seul DE Volt Directives de sécurité importantesCalibre Minimum Pour Rallonge Règles Spécifiques Additionnelles De Sûreté Description Fonctionnelle AVANT-PROPOSPièces DE LA Scie À Bras Radial Contenus DE BoitePièces DE LA Planche DE Banc Désemballage ET Nettoyage Lestimation DE Temps Dassemblee AssemblageOutils Nécessaires Pour L’ASSEMBLEE Attacher LES Pattes AU Socle DE LA ScieEnlever LA Lame ET LE PROTÈGE-LAME DE LA Scie Supports DU BancInsérer quatre vis à tête ronde de 6,3 mm 1/4 po Brides Pour Planche DE Banc ET Planches DE Banc Ajuster ET Vérifier LA Course DE LA Lame Éliminer LE « Talonnement » Aligner LA Lame DE LA Scie Avec LE BancRégler L’ÉCHELLE DE Sciage À L’INTÉRIEUR/À L’EXTÉRIEUR Attacher LA Lame ET LE PROTÈGE-LAMECouper Dans LES Planches DU Banc Démarrage ET Arrêt DE Scie FonctionnementVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Guide des pièces Ajustement DES Roulements À Billes SUR LA Voie Ajuster LA Tension DE LA Colonne ÉlévatriceChanger LA Position DE LA Poignée DE Fixation DU Bras Changer LA Position DE LA Poignée DE Fixation DE BiseauIndex DE Biseau Butée Positive Changer LA Position DE LA Poignée DE Fixation DE LA FourcheIndex DE Fourche Butée Positive Ajustement DU Séparateur ET DU Doigt ANTI-EFFET DE RebondRevêtement Auxiliaire DES Planches DU Banc TronçonnageUtiliser UNE Rallonge Découpe À Onglet Mixte Butée Pour LE TronçonnageDécoupe À Onglet Sciage EN LongSciage Vers L’INTÉRIEUR Sciage Vers L’EXTÉRIEURPoussoirs Poussoir Fabrication DUN PoussoirDepannage Entretien Pièces DE Rechange Entretien ET RéparationRemplacement Gratuit DE Létiquette Accessoiries GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesGuarde Estas Instrucciones Normas Generales DE Seguridad Conserve Estas InstruccionesInstrucciones de seguridad importantes Operación DE UNA Sola Fase CON 240 VoltiosCalibre Mínimo Para LOS Juegos DE Cables Normas Específicas Adicionales DE Seguridad Prologo Descripción FuncionalProtector DE LA Hoja Y Hendedor Piezas DE LA Sierra DE Brazo Radial Contenido DE CartonPiezas DE LA Tabla DE Mesa Desempaquetado y LimpiEZA Para Ensamblar LAS Patas a LA Base DE LA Sierra Herramientas DE Ensamblaje RequeridasEstimación DEL Tiempo DE Ensamblaje Para Ensamblar EL Gancho DE LlavesPara Retirar LA Hoja Y EL Protector DE LA Hoja DE LA Sierra Soportes DE LA Mesa Page Abrazaderas DE LA Tabla DE Mesa Y LAS Tablas DE Mesa Para Eliminar LA Inclinación Angular Heeling Para QUE LA Hoja DE LA Sierra Cuadre CON LA Mesa ¡Desconecte la máquina de la fuente del poderPara Montar LA Hoja Y EL Protector DE LA Hoja Para Cortar Entro DE LAS Tablas DE Mesa Cada vez que use la sierra, verifique que OperaciónArrancando Y Deteniendo LA Sierra Fijando EL Interruptor EN LA Posicion DE ApagadoGuía sobre las piezas Las tuercas hexagonales D contra la base de la columna Para Ajustar LOS Cojinetes Contra EL RielPara Ajustar LA Tensión EN LA Columna DE Elevación Contra chaveta H hasta que se elimine toda la holgura dePara Cambiar LA Posición DEL Mango DE Sujeción de bisel Índice DE Tope Positivo DEL Bisel Cambiar configuraciones o realizar reparaciones. UnÍndice DEL Tope Positivo DE LA Horquilla Para Ajustar EL Separador Y EL Dedo AntiretrocesoEL USO DE UNA Extensión DE Mesa Corte TransversalEL Revestimiento Auxiliar DE LA Mesa Tope DE Corte TransversalCorte Longitudinal Corte DE IngletesCorte DE Ingletes Compuestos Nunca toque el extremo libre deCorte Longitudinal Interno Corte Longitudinal ExternoVaras DE Empuje Construcción DE UNA Vara Para Empujar Localizacion DE Fallas Mantenimiento ServicioReemplazo Gratuito DE LAS Etiquetas DE Advertencia Identificación Delproducto AccesoriosExcepciones Garantia Para Otras LocalidadesDelta Machinery Highway 45 North Jackson, TN 800