Epson RS830 instruction manual Changing the Position of the Track ARM Clamping Handle

Page 21

ADJUSTING THE TENSION ON THE ELEVATING COLUMN

Elevating column tension is preset at the factory. “Play” may develop after extended use. To adjust:

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

1.Loosen the hex nuts (A) Fig. 49 and the gib adjustment screws (C).

2.Loosen the hex nuts (D) and turn the screws (E) until the column base wraps around the column securely and can be raised or lowered without binding. Tighten the hex nuts (D) against the column base.

3.Tighten the gib and adjustment screws (C) against the gib (H) until all side-to-side play is removed. Tighten the hex nuts (A) against column base.

 

F

 

H

 

 

 

E

D

A

C

 

 

B

 

 

 

 

Fig. 49

NOTE: After adjusting column tension, refer to “ADJUSTING SAW BLADE TRAVEL SQUARE WITH FENCE” to determine if saw blade travel was affected.

CHANGING THE POSITION OF THE TRACK ARM CLAMPING HANDLE

To reposition the track arm clamping handle (A) Fig. 50 when it does not lock in a convenient position:

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

1.Loosen and remove the track arm clamping lever (A) Fig. 50. Push the hex bolt (B) Fig. 51 back through the hole until the head of the bolt is out of the recessed bushing (C).

NOTE: The track arm clamping lever has a left-hand thread.

2.Rotate hex bolt (B) Fig. 51 in the desired direction.

3.Push the hex bolt (B) Fig. 51 back through hole. Check to see if the head of hex bolt is seated properly in the recessed bushing (C). Attach the track arm clamping lever.

NOTE: If the track arm clamping lever (A) Fig. 49 tightens before approximately four turns, the clamping bushings (one of which is shown at (C) Fig. 51 may have rotated. These bushings should seat completely inside the track (D). If they do not, slightly loosen the clamping lever (A) Fig. 50 and rotate the clamping bushing (C) Fig. 51 until it seats. Check to see if you need to rotate the bushing on the clamp lever side also.

NOTE: The flats on the clamping bushings should face the front of the saw.

NOTE: The clamp lever (A) Fig. 50 will thread at one of two positions. If, after making the adjustment, the clamp lever (A) tightens 180° from where desired, slowly unscrew clamp lever (A) while holding in on the hex bolt (B). When the clamp lever (A) comes off of the hex bolt (B), rotate the clamp lever (A) 180°. Thread the clamp lever.

Fig. 50

A

B

D

C

Fig. 51

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RS830 Important Safety Instructions Table of ContentsGrounding Instructions General SAFETY RULESFig. C Volt Single Phase OperationAmpere Rating Minimum Gauge for Cord SetsAdditional Specific Safety Rules Functional Description How to avoid them and protect yourself from possible injurySAW Blade Guard and Splitter KickbacksCarton Contents Unpacking and Cleaning Assembly Tools RequiredAssembly Time Estimate Attaching the Legs to the SAW Base Attaching the Wrench HookRemoving the Blade and Blade Guard from the SAW Table Supports Page Table Board Clamps and Table Boards Adjusting and Checking SAW Blade Travel Removing Heeling Attaching the Blade and Blade Guard Adjusting IN/OUT RIP ScaleCutting Into the Table Boards Starting and Stopping OperationGuide to Controls Locking the Switch in the OFF PositionAdjusting the Ball Bearings Against the Track Changing the Position of the Track ARM Clamping Handle Adjusting the Tension on the Elevating ColumnChanging the Position of the Yoke Clamp Handle Changing the Position of the Bevel Clamp HandlePositive Stop Yoke Index Positive Stop Bevel IndexUsing a Table Extension Adjusting the Splitter and ANTI-KICKBACK FingersCROSS-CUTTING Auxiliary Table Board FacingMiter Cutting CROSS-CUT StopAdjusting the Splitter and ANTI-KICKBACK Compound Miter CuttingRipping Keep Machine Clean TroubleshootingFailure to Start Lubrication & RUST PROTECTIONPush Stick Accessories ServiceWarranty Replacement Parts Service and RepairsFree warning label replacement Mesures DE Sécurité Définitions LES Instructions Importantes DE SureteConserver CES Directives Règles DE Sécurité GénéralesDirectives de sécurité importantes Operation DE Phase DE Seul DE VoltCalibre Minimum Pour Rallonge Règles Spécifiques Additionnelles De Sûreté AVANT-PROPOS Description FonctionnelleContenus DE Boite Pièces DE LA Scie À Bras RadialPièces DE LA Planche DE Banc Désemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLEE AssemblageLestimation DE Temps Dassemblee Attacher LES Pattes AU Socle DE LA ScieSupports DU Banc Enlever LA Lame ET LE PROTÈGE-LAME DE LA ScieInsérer quatre vis à tête ronde de 6,3 mm 1/4 po Brides Pour Planche DE Banc ET Planches DE Banc Ajuster ET Vérifier LA Course DE LA Lame Aligner LA Lame DE LA Scie Avec LE Banc Éliminer LE « Talonnement »Attacher LA Lame ET LE PROTÈGE-LAME Régler L’ÉCHELLE DE Sciage À L’INTÉRIEUR/À L’EXTÉRIEURCouper Dans LES Planches DU Banc Fonctionnement Démarrage ET Arrêt DE ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Guide des pièces Ajuster LA Tension DE LA Colonne Élévatrice Ajustement DES Roulements À Billes SUR LA VoieChanger LA Position DE LA Poignée DE Fixation DE Biseau Changer LA Position DE LA Poignée DE Fixation DU BrasIndex DE Fourche Butée Positive Changer LA Position DE LA Poignée DE Fixation DE LA FourcheIndex DE Biseau Butée Positive Ajustement DU Séparateur ET DU Doigt ANTI-EFFET DE RebondTronçonnage Revêtement Auxiliaire DES Planches DU BancUtiliser UNE Rallonge Découpe À Onglet Butée Pour LE TronçonnageDécoupe À Onglet Mixte Sciage EN LongSciage Vers L’EXTÉRIEUR Sciage Vers L’INTÉRIEURPoussoirs Fabrication DUN Poussoir PoussoirPièces DE Rechange Entretien ET Réparation Depannage EntretienRemplacement Gratuit DE Létiquette Garantie AccessoiriesInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESGuarde Estas Instrucciones Conserve Estas Instrucciones Normas Generales DE SeguridadOperación DE UNA Sola Fase CON 240 Voltios Instrucciones de seguridad importantesCalibre Mínimo Para LOS Juegos DE Cables Normas Específicas Adicionales DE Seguridad Descripción Funcional PrologoProtector DE LA Hoja Y Hendedor Contenido DE Carton Piezas DE LA Sierra DE Brazo RadialPiezas DE LA Tabla DE Mesa Desempaquetado y LimpiEZA Estimación DEL Tiempo DE Ensamblaje Herramientas DE Ensamblaje RequeridasPara Ensamblar LAS Patas a LA Base DE LA Sierra Para Ensamblar EL Gancho DE LlavesPara Retirar LA Hoja Y EL Protector DE LA Hoja DE LA Sierra Soportes DE LA Mesa Page Abrazaderas DE LA Tabla DE Mesa Y LAS Tablas DE Mesa Para Eliminar LA Inclinación Angular Heeling ¡Desconecte la máquina de la fuente del poder Para QUE LA Hoja DE LA Sierra Cuadre CON LA MesaPara Montar LA Hoja Y EL Protector DE LA Hoja Para Cortar Entro DE LAS Tablas DE Mesa Arrancando Y Deteniendo LA Sierra OperaciónCada vez que use la sierra, verifique que Fijando EL Interruptor EN LA Posicion DE ApagadoGuía sobre las piezas Para Ajustar LA Tensión EN LA Columna DE Elevación Para Ajustar LOS Cojinetes Contra EL RielLas tuercas hexagonales D contra la base de la columna Contra chaveta H hasta que se elimine toda la holgura dePara Cambiar LA Posición DEL Mango DE Sujeción de bisel Índice DEL Tope Positivo DE LA Horquilla Cambiar configuraciones o realizar reparaciones. UnÍndice DE Tope Positivo DEL Bisel Para Ajustar EL Separador Y EL Dedo AntiretrocesoEL Revestimiento Auxiliar DE LA Mesa Corte TransversalEL USO DE UNA Extensión DE Mesa Tope DE Corte TransversalCorte DE Ingletes Compuestos Corte DE IngletesCorte Longitudinal Nunca toque el extremo libre deCorte Longitudinal Externo Corte Longitudinal InternoVaras DE Empuje Construcción DE UNA Vara Para Empujar Servicio Localizacion DE Fallas MantenimientoReemplazo Gratuito DE LAS Etiquetas DE Advertencia Accesorios Identificación DelproductoExcepciones Para Otras Localidades GarantiaDelta Machinery Highway 45 North Jackson, TN 800
Top Page Image Contents