Epson RS830 instruction manual Cross-Cutting, Adjusting the Splitter and ANTI-KICKBACK Fingers

Page 23

ADJUSTING THE SPLITTER AND ANTI-KICKBACK FINGERS

To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. An accidental start-up can cause injury.

During ripping operations, the splitter (A) Fig. 56 must ride in the saw kerf and the anti-kickback fingers (B) should touch the workpiece to prevent kickback.

1.Set the saw up in the ripping position with the blade guard lowered on the in-feed side to act as a holddown.

2.Start a piece of material through the saw (Fig. 56).

3.Shut the saw off, and disconnect it from the power source.

4.Adjust the arm (C) Fig. 56 so that it is vertical and the

splitter (A) is in the saw kerf.

 

 

 

 

 

 

 

 

 

5. If the splitter (A) Fig. 56 does not align with the saw

 

 

 

 

 

 

 

 

C

kerf, loosen the hex nuts (D), and position the splitter

 

 

 

 

 

 

 

 

 

(A) into the saw kerf. Tighten the hex nuts (D) against

 

 

 

 

 

 

 

 

 

the arm (C). The straight side of the splitter should

 

 

 

 

 

 

 

 

 

 

 

A

be toward the blade (Fig. 56), and the anti-kickback

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

fingers should rest on the workpiece.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: The clamp knob for arm (C) must be tight. Move

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

arm (C) front to back while tightening clamp knob with

 

 

 

 

 

 

 

 

 

other hand to be sure clamp is firmly seated and tight.

Fig. 56

6. Pull backward on the workpiece to determine if the anti-kickback fingers bite into the material and prevent

further backward movement. If necessary, readjust the height of the arm (C) Fig. 56.

AUXILIARY TABLE BOARD FACING

To prevent repeated cutting into the table surface which will eventually cause the table to sag, you can cut an auxiliary table board facing and fit it to the table. Make it from 1/4" plywood or particle board. Cut it to a size that will cover all of the table boards in front of the fence. Place the auxiliary table board facing flat on the table and butt it against the table fence. Fasten it to the table with a small brad or finish nail in each corner.

USING A TABLE EXTENSION

When a table extension more than 24" long is attached to the saw, use a sturdy outrigger support or secure the stand or bench to the floor.

MACHINE USE

To reduce the risk of injury, turn unit off and disconnect the machine from the power source before installing and removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

Before connecting the radial arm saw to the power source or operating the saw, always inspect the guard and splitter for proper operation alignment and clearance with the saw blade. Personal injury may result.

CROSS-CUTTING

To reduce the risk of injury, turn unit off and disconnect the machine from the power source before installing and removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

NEVER touch the "free end" of the workpiece or a "free Piece" that is cut off while the power is "ON" and/or the saw blade is rotating. The piece may contact the blade resulting in a thrown workpiece and possible injury.

NEVER use a length stop on the free end of the workpiece when crosscutting. In short, the cut-off piece in any through-sawing (cutting completely through the workpiece) operation must never be confined

-it must be allowed to move away from the saw blade to prevent contact with the blade resulting in a thrown workpiece and possibly injury.

Use caution when starting the cut to prevent binding of the guard against the workpiece resulting in damage to the saw and possible injury.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents RS830 Important Safety Instructions Table of ContentsGrounding Instructions General SAFETY RULESFig. C Volt Single Phase OperationAmpere Rating Minimum Gauge for Cord SetsAdditional Specific Safety Rules Kickbacks How to avoid them and protect yourself from possible injuryFunctional Description SAW Blade Guard and SplitterCarton Contents Assembly Time Estimate Unpacking and CleaningAssembly Tools Required Removing the Blade and Blade Guard from the SAW Attaching the Legs to the SAW BaseAttaching the Wrench Hook Table Supports Page Table Board Clamps and Table Boards Adjusting and Checking SAW Blade Travel Removing Heeling Attaching the Blade and Blade Guard Adjusting IN/OUT RIP ScaleCutting Into the Table Boards Starting and Stopping OperationGuide to Controls Locking the Switch in the OFF PositionAdjusting the Ball Bearings Against the Track Changing the Position of the Track ARM Clamping Handle Adjusting the Tension on the Elevating ColumnPositive Stop Bevel Index Changing the Position of the Bevel Clamp HandleChanging the Position of the Yoke Clamp Handle Positive Stop Yoke IndexAuxiliary Table Board Facing Adjusting the Splitter and ANTI-KICKBACK FingersUsing a Table Extension CROSS-CUTTINGMiter Cutting CROSS-CUT StopRipping Adjusting the Splitter and ANTI-KICKBACKCompound Miter Cutting Lubrication & RUST PROTECTION TroubleshootingKeep Machine Clean Failure to StartPush Stick Replacement Parts Service and Repairs ServiceAccessories WarrantyFree warning label replacement Mesures DE Sécurité Définitions LES Instructions Importantes DE SureteConserver CES Directives Règles DE Sécurité GénéralesDirectives de sécurité importantes Operation DE Phase DE Seul DE VoltCalibre Minimum Pour Rallonge Règles Spécifiques Additionnelles De Sûreté AVANT-PROPOS Description FonctionnellePièces DE LA Planche DE Banc Contenus DE BoitePièces DE LA Scie À Bras Radial Désemballage ET Nettoyage Attacher LES Pattes AU Socle DE LA Scie AssemblageOutils Nécessaires Pour L’ASSEMBLEE Lestimation DE Temps DassembleeSupports DU Banc Enlever LA Lame ET LE PROTÈGE-LAME DE LA ScieInsérer quatre vis à tête ronde de 6,3 mm 1/4 po Brides Pour Planche DE Banc ET Planches DE Banc Ajuster ET Vérifier LA Course DE LA Lame Aligner LA Lame DE LA Scie Avec LE Banc Éliminer LE « Talonnement »Attacher LA Lame ET LE PROTÈGE-LAME Régler L’ÉCHELLE DE Sciage À L’INTÉRIEUR/À L’EXTÉRIEURCouper Dans LES Planches DU Banc Verrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE Scie Guide des pièces Ajuster LA Tension DE LA Colonne Élévatrice Ajustement DES Roulements À Billes SUR LA VoieChanger LA Position DE LA Poignée DE Fixation DE Biseau Changer LA Position DE LA Poignée DE Fixation DU BrasAjustement DU Séparateur ET DU Doigt ANTI-EFFET DE Rebond Changer LA Position DE LA Poignée DE Fixation DE LA FourcheIndex DE Fourche Butée Positive Index DE Biseau Butée PositiveUtiliser UNE Rallonge TronçonnageRevêtement Auxiliaire DES Planches DU Banc Sciage EN Long Butée Pour LE TronçonnageDécoupe À Onglet Découpe À Onglet MixtePoussoirs Sciage Vers L’EXTÉRIEURSciage Vers L’INTÉRIEUR Fabrication DUN Poussoir PoussoirPièces DE Rechange Entretien ET Réparation Depannage EntretienRemplacement Gratuit DE Létiquette Garantie AccessoiriesGuarde Estas Instrucciones Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Conserve Estas Instrucciones Normas Generales DE SeguridadOperación DE UNA Sola Fase CON 240 Voltios Instrucciones de seguridad importantesCalibre Mínimo Para LOS Juegos DE Cables Normas Específicas Adicionales DE Seguridad Protector DE LA Hoja Y Hendedor Descripción FuncionalPrologo Piezas DE LA Tabla DE Mesa Contenido DE CartonPiezas DE LA Sierra DE Brazo Radial Desempaquetado y LimpiEZA Para Ensamblar EL Gancho DE Llaves Herramientas DE Ensamblaje RequeridasEstimación DEL Tiempo DE Ensamblaje Para Ensamblar LAS Patas a LA Base DE LA SierraPara Retirar LA Hoja Y EL Protector DE LA Hoja DE LA Sierra Soportes DE LA Mesa Page Abrazaderas DE LA Tabla DE Mesa Y LAS Tablas DE Mesa Para Eliminar LA Inclinación Angular Heeling ¡Desconecte la máquina de la fuente del poder Para QUE LA Hoja DE LA Sierra Cuadre CON LA MesaPara Montar LA Hoja Y EL Protector DE LA Hoja Para Cortar Entro DE LAS Tablas DE Mesa Fijando EL Interruptor EN LA Posicion DE Apagado OperaciónArrancando Y Deteniendo LA Sierra Cada vez que use la sierra, verifique queGuía sobre las piezas Contra chaveta H hasta que se elimine toda la holgura de Para Ajustar LOS Cojinetes Contra EL RielPara Ajustar LA Tensión EN LA Columna DE Elevación Las tuercas hexagonales D contra la base de la columnaPara Cambiar LA Posición DEL Mango DE Sujeción de bisel Para Ajustar EL Separador Y EL Dedo Antiretroceso Cambiar configuraciones o realizar reparaciones. UnÍndice DEL Tope Positivo DE LA Horquilla Índice DE Tope Positivo DEL BiselTope DE Corte Transversal Corte TransversalEL Revestimiento Auxiliar DE LA Mesa EL USO DE UNA Extensión DE MesaNunca toque el extremo libre de Corte DE IngletesCorte DE Ingletes Compuestos Corte LongitudinalVaras DE Empuje Corte Longitudinal ExternoCorte Longitudinal Interno Construcción DE UNA Vara Para Empujar Servicio Localizacion DE Fallas MantenimientoReemplazo Gratuito DE LAS Etiquetas DE Advertencia Excepciones AccesoriosIdentificación Delproducto Para Otras Localidades GarantiaDelta Machinery Highway 45 North Jackson, TN 800
Top Page Image Contents