DeWalt DW713 instruction manual Special Cuts, Bevel Setting Type of CUT

BEVEL SETTING TYPE OF CUT

	LEFT SIDE, INSIDE CORNER:
33.85°	1.	Top of molding against fence
	2.	Miter table set right 31.62°
	3.	Save left end of cut
	RIGHT SIDE, INSIDE CORNER:
33.85°	1.	Bottom of molding against fence
	2.	Miter table set left 31.62°
	3.	Save left end of cut
	LEFT SIDE, OUTSIDE CORNER:
33.85°	1.	Bottom of molding against fence
	2.	Miter table set left 31.62°
	3.	Save right end of cut
	RIGHT SIDE, OUTSIDE CORNER:
33.85°	1.	Top of molding against fence
	2.	Miter table set right 31.62°
	3.	Save right end of cut

When setting bevel and miter angles for all compound miters, remember that:

The angles presented for crown moldings are very precise and difficult to set exactly. Since they can easily shift slightly and very few rooms have exactly square corners, all settings should be tested on scrap molding.

PRETESTING WITH SCRAP MATERIAL IS

EXTREMELY IMPORTANT!

ALTERNATIVE METHOD FOR CUTTING CROWN MOLDING

Place the molding on the table at an angle between the fence and the saw table, as shown in Figure 30. Use of the crown molding fence accessory (DW7084) is highly recommended because of its degree of accuracy and convenience. The crown molding fence accessory is available at extra cost from your local dealer.

FIG. 29

FENCE

TABLE

CROWN MOLDING FLAT ON TABLE AND

AGAINST FENCE

FIG. 30

BOTTOM SIDE
OF MOLDING	DW 7084 CROWN
TOP SIDE	MOLDING FENCE
OF MOLDING
	TABLE
FENCE

CROWN MOLDING BETWEEN FENCE AND TABLE

FIG. 31

English

BLADE

FENCERIGHT

FIG. 32

	BLADE
FENCE	WRONG

The advantage to cutting crown molding using this method is that no bevel cut is required. Minute changes in the miter angle can be made without affecting the bevel angle. This way, when corners other than 90° are encountered, the saw can be quickly and easily adjusted for them. Use the crown molding fence accessory (DW7084) to maintain the angle at which the molding will be on the wall.

INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND BASE OF THE SAW FOR ALL CUTS

1.Angle the molding so the bottom of the molding (part which goes against the wall when installed) is against the fence and the top of the molding is resting on the base of the saw, as shown in Figure 30.

2.The angled “flats” on the back of the molding must rest squarely on the fence and base of the saw.

INSIDE CORNER:		OUTSIDE CORNER:
Left side		Left side
1.	Miter right at 45°	1.	Miter left at 45°
2.	Save right side of cut	2.	Save right side of cut
Right side		Right side
1.	Miter left at 45°	1.	Miter right at 45°
2.	Save left side of cut	2.	Save left side of cut

Special Cuts

NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.

ALUMINUM CUTTING

ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM. These are available at your local DEWALT retailer or DEWALT service center. Certain workpieces, due to their size, shape or surface finish, may require the use of a clamp or fixture to prevent movement during the cut. Position the material so that you will be cutting the thinnest cross section, as shown in Figure 31. Figure 32 illustrates the wrong way to cut these extrusions. Use a stick wax cutting lubricant when cutting aluminum. Apply the stick wax directly to the saw blade before cutting. Never apply stick wax to a moving blade.

13