DeWalt DW713 instruction manual Installing a Blade, Adjustments

Page 8

FIG. 4

English

FIG. 5

FIG. 6

OUTER

BLADE CLAMP

SCREW WASHER

LOCK

DOWN

PIN

GUARD

GUARD

BRACKET

SCREW

WRENCH

BLADE

INNER CLAMP

WASHER

5.Keeping the button depressed, use the other hand and the wrench provided to loosen the blade screw. (Turn clockwise, left-hand threads.)

6.Remove the blade screw, outer blade clamp, and blade. The inner blade clamp may be left on the spindle.

Installing a Blade

1.Unplug the saw.

2.With the arm raised, the lower guard held open and the guard bracket, place the blade on the spindle against the inner blade clamp with the teeth at the bottom of the blade pointing toward the back of the saw.

3.Assemble the outer blade clamp onto the spindle.

4.Install the blade screw and, engaging the spindle lock, tighten the screw firmly with wrench provided. (Turn counterclockwise, left-hand threads.)

5.Return the guard bracket to its original position and firmly tighten the guard bracket screw to hold bracket in place.

WARNING:

The guard bracket must be returned to its original position and the screw tightened before activating the saw.

Failure to do so may allow the guard to contact the spinning saw blade resulting in damage to the saw and severe personal injury.

Transporting the Saw

WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instructions.

WARNING: To reduce the risk of serious personal injury, ALWAYS lock the miter lock handle, bevel lock handle, down lock pin, and fence adjustment knob before transporting saw.

In order to conveniently carry the miter saw from place to place, a carrying handle has been included on the top of the saw arm, as shown in Figure 3. To transport the saw, lower the arm and depress the lock down pin shown in Figure 4.

ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instructions.

NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw.

Once made, these adjustments should remain accurate. Take a little time now to follow these directions carefully to maintain the accuracy of which your saw is capable.

MITER SCALE ADJUSTMENT

Place a square against the saw’s fence and blade, as shown in Figure 7. (Do not touch the tips of the blade teeth with the square. To do so will cause an inaccurate measurement.) Unlock miter lock lever (see Fig. 8) and swing the miter arm until the miter detent locks it at the 0˚ miter position. Do not lock miter lock lever. If the saw blade is not exactly perpendicular to the fence, loosen the three screws that hold the miter scale to the base (shown in Fig. 8) and move the scale/miter arm assembly left or right until the blade is perpendicular to the fence, as measured with the square. Retighten the three screws. Pay no attention to the reading of the miter pointer at this point.

MITER POINTER ADJUSTMENT

Unlock miter lock lever and squeeze the miter detent to move the miter arm to the zero position, as shown in Figure 8. Unlock the miter lock lever to allow the miter detent to snap into place as you rotate the miter arm past zero. Observe the pointer and miter scale through the viewing opening shown in Figure 9. If the pointer does not indicate exactly zero, loosen the pointer screw, adjust the pointer to 0˚ and retighten.

BEVEL SQUARE TO TABLE

To align the blade square to the rotary table, lock the arm in the down position. Place a square against the blade taking care to not have the square on top of a tooth, as shown in Figure 10B. Loosen the Bevel Clamp Knob so that you can move the Bevel Arm. Move the Bevel Arm as necessary so that the blade is at 0° bevel to the table. If the Bevel Arm needs adjustment, loosen the lock nut on the right side Bevel Stop as shown in Figure 11, and adjust the stop screw as necessary. Hold the stop screw in place and tighten the lock nut.

BEVEL POINTER

If the bevel pointer does not indicate zero, loosen the screw that holds it in place and move the pointer as necessary.

Suggestion: For accuracy, set the top edge so that it aligns with zero.

BEVEL STOP

To set the 45° bevel stop shown in Figure 12, first loosen the left side fence clamping knob and slide the left side fence as far as it will go to the left. Move the arm to the left until it stops on the left bevel stop screw. If the bevel pointer does not indicate exactly 45°, loosen the left side bevel stop lock nut and turn the screw downwards. Move the arm to the left and tighten the bevel clamp knob firmly

6

Image 8
Contents Dewalt Table of Contents Definitions Safety Guidelines Important Safety InstructionsSafety Instructions For All Tools Double InsulationAdditional Safety Rules For Miter Saws Familiarization Electrical ConnectionUnpacking Your Saw Accessories SpecificationsOptional Accessories Removing the Blade Changing or Installing a New Saw BladeBench Mounting Installing a Blade AdjustmentsAutomatic Electric Brake Fence AdjustmentGuard Actuation and Visibility Miter Lock Adjustment FIG SwitchBrushes OperationBevel Cuts Quality of CUTBody and Hand Position FIG Clamping the WorkpieceTo Install Clamp Sold Separately Support for Long PiecesWhen Mitering to the Right When Mitering to the LeftExamples Cutting Compound MitersCutting Crown Molding Molding Vertically Against the FenceInside Corner Bevel Setting Type of CUT Special CutsMaintenance Service InformationThree Year Limited Warranty RepairsTroubleshooting Guide Saw will not startSET this Bevel Angle on SAW Angle of Side of BOX Angle aTable des matières Définitions Lignes directrices en Matière de sécurité Consignes DE Sécurité ImportantesDouble isolation Fiches polariséesRègles de sécurité supplémentaires pour les scies à onglets SUR LE Boîtier DU Moteur Accessoires facultatifs Connexion électriqueDéballage de la scie FamiliarisationDescription DES Lames Application Diamètre Dents AccessoiresMontage sur établi Importantes Directives DE Sécurité Changement ou pose d’une lame de scie neuveDépose de la lame Pose d’une lameAvertissement RéglagesFrein Électrique Automatique Réglage DU GuideActivation ET Visibilité DU PARE-MAIN Balais FonctionnementCoupes EN Biseau Qualité DE CoupeFixation DE LA Pièce Installation DE LA Bride Vendus SéparémentPosition DU Corps ET DES Mains FIG Soutien DES Pièces Longues Découpe DE Moulures DE Garnissage ET D’AUTRES CadresExemples Découpe À Onglets MixtesPour L’ASSEMBLAGE EN Onglet À Droite Pour L’ASSEMBLAGE EN Onglet À GaucheDécoupe DE Moulures D’EMBASE LA VERTICALE, Contre LE GuideCôté gauche Découpe DE Moulure CouronnéeDécoupes spéciales Type DE CoupeMéthode Alternative DE Découpe DE Moulures Couronnées Matériau ArquéEntretien Garantie limitée trois ansInformation sur les réparations ou l’entretien RéparationsGuide de dépannage La scie ne démarre pasTableau 1 Coupe À Onglet Mixte Índice de temas Definiciones Normas de seguridad Instrucciones DE Seguridad ImportantesDoble aislamiento Enchufes polarizadosEn amperios Peligro Manténgase Alejado DE LA Hoja Conexión eléctrica Desembalar la sierraFamiliarizarse con la herramienta EspecificacionesDescripciones DE LAS Hojas Aplicación Diámetro Dientes AccesoriosMontaje en el banco de trabajo Instalación de la hoja Cambio o instalación de una hoja de sierra nuevaExtracción de la hoja Advertencia AjustesFreno Eléctrico Automático Regulación DE LA GuíaAccionamiento Y Visibilidad DEL Protector Cepillos FuncionamientoCortes Biselados Calidad DEL CortePara Instalar LA Abrazadera SE Venden POR Separado Posición DEL Cuerpo Y LAS Manos FIGSujeción DE LA Pieza DE Trabajo Soporte DE Piezas Largas Corte DE Molduras DE Terminación Y Otros MarcosEjemplos Corte DE Ingletes CompuestosEscala Vernier Inglete a LA DerechaInglete a LA Izquierda Corte DE Molduras DE BaseCorte DE Molduras DE Corona Configuración Tipo DE Corte DE Bisel Cortes especialesCorte DE Aluminio Material CurvadoMantenimiento ReparacionesPóliza de Garantía Garantía limitada de tres añosGUADALAJARA, JAL MEXICO, D.F. MERIDA, YUC MONTERREY, N.LPUEBLA, PUE QUERETARO, QROGuía de detección de problemas La sierra no enciendeÁngulo DEL Lado DE LA Caja Ángulo a Tabla 1 Corte DE Inglete CompuestoFije Este Ángulo DE Bisel EN LA Sierra DW713
Related manuals
Manual 52 pages 36.16 Kb