English
Press down lightly on the operating handle and pull out the lock down pin, as shown in Figure 4. Gently release the downward pressure and allow the arm to rise to its full height. Use the lock down pin when carrying the saw from one place to another. Always use the carrying handle to transport the saw or the hand indentations shown in Figure 3.
Specifications
CAPACITY OF CUT
50° miter left and right |
|
| |
48° bevel left: 3° right |
|
| |
0° miter |
|
|
|
Max. Height 3.5" (89 mm) | Result Width 3.5" (89 mm) | ||
Max. Width 6.1" (155 mm) | Result Height 1.25" (32 mm) | ||
45° miter |
|
|
|
Max. Height 3.5" (89 mm) | Result Width 2.4" (61 mm) | ||
Max. Width 4.2" (107 mm) | Result Height 1.25" (32 mm) | ||
45° bevel |
|
|
|
Max. Height | 2.3" (58 mm) | Result Width | 3.5" (89 mm) |
Max. Width | 6.1" (155 mm) | Result Height | .75" (19 mm) |
31.62° miter and 33.85° bevel |
|
| |
Max. Width | 5.25" (133 mm) | Result Height | .9" (23 mm) |
DRIVE |
|
|
|
120 Volt Motor |
|
|
|
2200 Watts |
| 15 Amp Motor |
|
5000 RPM |
| Cut Helical Gears with Roller and Ball Bearings | |
Carbide Tooth Blade | Automatic Electric Brake | ||
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in selecting and using accessories.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled. Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support (see drawing). It is used to make repetitive cuts of the same length from 0 to 42" (107 cm).
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053 (Included with some models)
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the sawdust produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Laser Guide System: DW7187
Powered by the saw, the bright laser line delivers enhanced visibility in low and high light locations. Easy to install.
Miter Saw LED Worklight System: DWS7085
Lighting used for greater visibility and cutting alignment during operation. Easy to install.
Miter Saw Replacement Kerf Plate: DW7055
This durable plastic uncut plate limits blade tear out.
DW7082
DW7080
LOCKNUTS
END PLATE
DW7187
DWS7085
DW7084
SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades or blades with hook angles in excess of 7˚.
BLADE DESCRIPTIONS
APPLICATION | DIAMETER | TEETH |
Construction Saw Blades (thin kerf with | ||
General Purpose | 10" (254 mm) | 40 |
Fine Crosscuts | 10" (254 mm) | 60 |
Woodworking Saw Blades (provide smooth, clean cuts) | ||
Fine crosscuts | 10" (254 mm) | 80 |
10" (254 mm) | 80 | |
NOTE: For cutting
ACCESSORIES
WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product.
4