DeWalt Compound Miter Saw manual Outside Corner, Proper CUT Improper CUT

Page 14

English

2. Save left side of cut Right side

1.Miter Right 45°

2.Save right side of cut

OUTSIDE CORNER:

Left side

1.Miter right at 45°

2.Save left side of cut

Right side

1.Miter left at 45°

2.Save right side of cut

Material up to 3.9" (3-7/8)" can be cut as described above. For wider boards [up to 5.5" (5-1/2")] several minor concessions must be made.

When cutting a board between 3.9" (3-7/8") and 5.5" (5-1/2") in width the roller on the tip of the guard will hang up on the workpiece. If this occurs, simply place your right thumb on the upper side of the guard and roll the guard up just enough to clear the workpiece, as shown in Figure 25. Once you have cleared the workpiece, you can release the guard and it will continue to open as the cut progresses.

When mitering to the right side of a base molding wider than 3.9" (3-7/8") standing vertically against the fence as in Figure 22, the saw can only cut through the board up to 1 inch from the end of the board. Trying to cut more than an inch will cause the saw’s gear case to interfere with the workpiece. If you want to cut base molding between 3-7/8" and 5-1/2" wide vertically follow the directions on next page.

CUTTING 3-7/8"– 5-1/2" BASE MOLDING VERTICALLY AGAINST THE FENCE

FIG. 16

PROPER CUT

IMPROPER CUT

Position molding as shown in Figure 22

All cuts made with the back of the molding against the fence

INSIDE CORNER: Left side

1.Position molding with bottom of molding against the base of the saw

2.Miter left 45°

3.Save left side of cut

Right side

1.Position molding with top of the molding resting on the base of the saw

2.Miter left 45°

3.Save left side of cut

OUTSIDE CORNER:

Left side

 

 

FENCE

 

ADJUST

USE

ALWAYS

BEFORE

PROPERLY

 

ANGERAWAAYDE

D

KEEOPMBL

 

FR

ER

NG

DA

DJUST￿FENCE

ALWAYS￿APROPERLY￿BEFORE￿US

GER

N

AY

DA KFEEROPMAWBLADE

ER NG DA

1.Position molding with bottom of molding against the base of the saw

2.Miter right 45°

3.Save left side of cut

PROPER CUT

IMPROPER CUT

10

Image 14
Contents English DW705 Copyright 2001 Guide D´UTILISATION Manual DE Instrucciones Table of Contents Double Insulation Important Safety InstructionsSafety Instructions For All Tools Polarized PlugsAdditional Safety Rules For Miter Saws Electrical Connection SpecificationsOptional Accessories Unpacking Your SawBench Mounting AccessoriesInstalling a New Saw Blade Fig Rear Lower Guard Adjustment Installing Extension KitAdjustments Transporting the SawBevel Stop Fence AdjustmentBevel Pointer Guard Actuation and VisibilityBrushes OperationSupport for Long Pieces Body and Hand Position see FIGClamping the Workpiece Cutting Compound MitersDual Range Miter Scale When Mitering to the RightWhen Mitering to the Left Vernier ScaleOutside Corner Proper CUT Improper CUTInside Corner Angle aMiter Scale Kerf Plate Miter ARM Cutting Crown MoldingRight Bevel Setting Type of CUTAlternative Method for Cutting Crown Molding Wrong Special Cuts Never Make ANY CUT Unless the Material isDAY no Risk Satisfaction Guarantee MaintenanceFull Warranty Secured on the Table and Against the FenceWHAT’S WRONG? What to DO… Trouble Shooting GuideBe Sure to Follow Safety Rules and Instructions DEWALT… Conçu Pour LE Chantier DewaltCorniches Entretien Guide DE Dépannage GarantiePour tous les outils Double isolationFiche polarisée DW705 Français Familiarisation Connexion électriqueDéballage Fiche techniqueMontage sur établi Accessoires facultatifsAccessoires Réglage du protecteur inférieur arrière Installation de la lame FigRallonge de plateau latérale certains modèles seulement Rainurage de la plaqueTransport de la scie Réglage DE L’INDICATEUR D’ONGLETButée DU Biseau Réglage DU Biseau EN ÉquerreIndicateur DE Biseau Réglage DU GuideBalais FonctionnementFixation DE LA Piece À Ouvrer Qualité DE LA CoupePosition DU Corps ET DES Mains FIG Mettre la scie hors tension et la débrancherMoulures ET Autres Cadres Soutien DES Grandes PiecesCADRES, Boîtes Vides ET Autres Projets À Quatre Côtés Coupes EN Onglets À Droite Onglets MixtesÉchelle DU Vernier Coupes EN Onglets À GaucheCorniches Coin ExtérieurMoulure DE Base Placée À L’HORIZONTALE ET Coupe EN Biseau Tableau 1 Onglets Mixtes Réglage DU Biseau Type DE CoupeMatériau arqué Autre méthode de coupe de cornicheCoupe de l’aluminium Matériau largeGarantie complète EntretienDewalt DEWALT...PARA Trabajos PesadosContenido Clavijas polarizadas DW705 Instrucciones importantes de seguridadDoble aislamiento Instrucciones de seguridad para todas las herramientasMás No más Calibre promedio del alambre Instrucciones de seguridad adicionales para ingleteadorasCalibre mínimo requerido AWG para cables de extensión Familiarícese con su sierra Conexión eléctricaDesempaque su ingleteadora Tope DE Longitud Ajustable DW7051 AccesoriosMontaje en banco Ajuste de la guarda inferior trasera Instalación del disco FigExtensión lateral de la mesa para algunos modelos Corte de la placa de respaldoApague LA Sierra Antes DE Realizar Cualquier Ajuste Transporte de la sierraAjustes Ajuste DE LA Escala DEL IngleteIndicador DEL Ángulo DE Corte Ajuste DEL Indicador DE LA EscalaAjuste a Escuadra DEL Ángulo DE Corte DEL Disco Tope DEL BiselInterruptor CarbonesOperación Cortes CON SU SierraPosicion DE Cuerpo Y Manos VER Figura Cortes DE BiselCalidad DEL Corte Soporte Para Piezas Largas Sujecion DE LA Pieza DE TrabajoApague y desconecte la sierra Corte DE MARCOS, CAJAS, Y Otros Proyectos DE Cuatro LadosEscala Vernier Corte DE Inglete CompuestoEscala Doble DE Inglete Corte DE Inglete a LA DerechaCorte DE Molduras DE Remate Lado DerechoEsquina Exterior Ajuste DE Bisel Tipo DE Corte Metodo Alternativo Para Cortar Molduras DE RemateCorte de aluminio MantenimientoImportante Material arqueadoGuía para la solución de problemas frecuentes Garantía Completa