BLADE
WRONG | FIG. 28 |
FENCE
FIG. 29
RIGHT
TABLE 1 COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
|
| 5 |
| 10 |
|
|
|
|
|
|
|
|
|
| English |
|
|
|
| 15 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 20 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 25 |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| 30 |
|
|
|
|
|
|
SAW |
|
|
|
|
|
|
|
|
| 35 | SQUARE |
|
|
| |
|
|
|
|
|
|
|
|
| 40 |
|
| A) | |||
|
|
|
|
|
|
|
|
|
|
| 45 | BOX |
|
| |
| 5 |
| 10 | 15 |
|
|
|
|
|
|
| 50 | • |
| 26.5˚ |
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| ||||
SET THIS MITERANGLEON |
|
|
|
| 20 |
|
|
|
|
|
|
|
| ANGLE OF SIDE OF(ANGLEBOX | |
|
|
|
| 25 |
|
|
| 6 |
|
| 55 |
|
| ||
|
|
|
|
| 30 |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| - |
|
|
|
|
| ||||
|
|
|
|
|
|
| 35 | SIDED |
|
|
|
| |||
|
|
|
|
|
|
| 40 |
|
| 60 |
| ||||
5 |
|
|
|
|
|
|
|
|
|
| |||||
10 |
|
|
|
|
|
| BOX |
|
|
|
| ||||
15 | 20 |
|
| 8 |
| 45 |
|
|
|
| |||||
|
|
| 25 |
| - |
| 50 |
|
| 65 |
| ||||
|
|
|
| 30 |
| SIDED |
|
|
|
|
| ||||
SETTING |
|
|
| 35 |
|
| 55 |
|
|
|
| ||||
|
|
|
| 40 |
| BOX |
|
|
|
| |||||
|
|
|
|
|
|
|
|
| 70 | ||||||
|
|
|
|
| 45 | 60 |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| 50 |
| 65 |
|
|
|
| |||
|
|
|
|
|
| 55 |
|
|
|
| 75 | ||||
| DEGREE |
|
|
|
|
|
| 60 |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 70 |
|
|
|
|
| ||
|
|
|
|
|
|
| 65 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 70 | 75 |
|
|
| 80 |
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| MITER |
|
|
|
|
|
| 75 | 80 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 80 | 85 |
|
|
| 85 |
| |
| BEVEL DEGREE SETTING | 85 |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| 38˚ |
|
|
SET THIS BEVEL ANGLE ON SAW
FIG. 30
WRONG
This way, when corners other than 90 degrees are encountered, the saw can be quickly and easily adjusted for them. Use the crown molding fence accessory to maintain the angle at which the molding will be on the wall.
INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND BASE OF THE SAW FOR ALL CUTS:
1.Angle the molding so the bottom of the molding (part which goes against the wall when installed) is against the fence and the top of the molding is resting on the base of the saw, as shown in Figure 26A.
2.The angled “flats” on the back of the molding must rest squarely on the fence and base of the saw.
INSIDE CORNER:
Left side
1.Miter right at 45°
2.Save the right side of cut
Right side
1.Miter left at 45°
2.Save left side of cut
OUTSIDE CORNER:
Left side
1.Miter left at 45°
2.Save right side of cut
Right side
1.Miter right at 45°
2.Save left side of cut
SPECIAL CUTS
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS
13