DeWalt Compound Miter Saw Bevel Setting Type of CUT, Alternative Method for Cutting Crown Molding

Page 16

English

accurately set on your saw.) Since most rooms do not have angles of precisely 90 degrees, you will have to fine tune your settings anyway.

PRETESTING WITH SCRAP MATERIAL IS

EXTREMELY IMPORTANT!

INSTRUCTIONS FOR CUTTING CROWN MOLDING

LAYING FLAT AND USING THE COMPOUND FEATURES

1. Molding laying with broad back surface down flat on saw table (See Figure 26)

2. The settings below are for All Standard (U.S.) crown molding with 52° and 38° angles.

BEVEL SETTING

TYPE OF CUT

LEFT SIDE, INSIDE CORNER:

33.85° 1. Top of molding against fence

2.Miter table set right 31.62°

3.Save left end of cut

RIGHT SIDE, INSIDE CORNER:

33.85° 1. Bottom of molding against fence 2. Miter table set left 31.62°

3. Save left end of cut

LEFT SIDE, OUTSIDE CORNER:

33.85° 1. Bottom of molding against fence 2. Miter table set left 31.62°

3. Save right end of cut

RIGHT SIDE, OUTSIDE CORNER:

33.85° 1. Top of molding against fence 2. Miter table set right 31.62°

3. Save right end of cut

When setting bevel and miter angles for all

 

compound miters, remember that:

 

The angles presented for crown moldings are very

 

precise and difficult to set exactly. Since they can

 

easily shift slightly and very few rooms have exactly

FIG. 25

square corners, all settings should be tested on

 

scrap molding.

 

PRETESTING WITH SCRAP MATERIAL IS

 

EXTREMELY IMPORTANT!

 

ALTERNATIVE METHOD FOR CUTTING CROWN MOLDING

Place the molding on the table at an angle between the fence and the saw table, as shown in Figure 26A. Use of the crown molding fence accessory (DW7054) is highly recommended because of its degree of accuracy and convenience. The crown molding fence accessory is available at extra cost from your local dealer.

The advantage to cutting crown molding using this method is that no bevel cut is required. Minute changes in the miter angle can be made without affecting the bevel angle.

FIG. 23

FIG. 24

FIG. 26

FENCE

TABLE

CROWN MOLDING FLAT ON TABLE AND AGAINST FENCE

FIG. 26A

BOTTOM SIDE

 

OF MOLDING

DW 7054 CROWN

TOP SIDE

MOLDING FENCE

 

OF MOLDING

TABLE

 

FENCE

 

CROWN MOLDING BETWEEN FENCE AND TABLE

 

BLADE

RIGHT

FIG. 27

FENCE

 

12

Image 16
Contents English DW705 Copyright 2001 Guide D´UTILISATION Manual DE Instrucciones Table of Contents Important Safety Instructions Safety Instructions For All ToolsDouble Insulation Polarized PlugsAdditional Safety Rules For Miter Saws Specifications Optional AccessoriesElectrical Connection Unpacking Your SawInstalling a New Saw Blade Fig AccessoriesBench Mounting Installing Extension Kit AdjustmentsRear Lower Guard Adjustment Transporting the SawFence Adjustment Bevel PointerBevel Stop Guard Actuation and VisibilityBrushes OperationBody and Hand Position see FIG Clamping the WorkpieceSupport for Long Pieces Cutting Compound MitersWhen Mitering to the Right When Mitering to the LeftDual Range Miter Scale Vernier ScaleOutside Corner Proper CUT Improper CUTAngle a Miter Scale Kerf Plate Miter ARMInside Corner Cutting Crown MoldingAlternative Method for Cutting Crown Molding Bevel Setting Type of CUTRight Wrong Special Cuts Never Make ANY CUT Unless the Material isMaintenance Full WarrantyDAY no Risk Satisfaction Guarantee Secured on the Table and Against the FenceBe Sure to Follow Safety Rules and Instructions Trouble Shooting GuideWHAT’S WRONG? What to DO… DEWALT… Conçu Pour LE Chantier DewaltCorniches Entretien Guide DE Dépannage GarantieFiche polarisée DW705 Double isolationPour tous les outils Français Connexion électrique DéballageFamiliarisation Fiche techniqueAccessoires Accessoires facultatifsMontage sur établi Installation de la lame Fig Rallonge de plateau latérale certains modèles seulementRéglage du protecteur inférieur arrière Rainurage de la plaqueTransport de la scie Réglage DE L’INDICATEUR D’ONGLETRéglage DU Biseau EN Équerre Indicateur DE BiseauButée DU Biseau Réglage DU GuideBalais FonctionnementQualité DE LA Coupe Position DU Corps ET DES Mains FIGFixation DE LA Piece À Ouvrer Mettre la scie hors tension et la débrancherCADRES, Boîtes Vides ET Autres Projets À Quatre Côtés Soutien DES Grandes PiecesMoulures ET Autres Cadres Onglets Mixtes Échelle DU VernierCoupes EN Onglets À Droite Coupes EN Onglets À GaucheMoulure DE Base Placée À L’HORIZONTALE ET Coupe EN Biseau Coin ExtérieurCorniches Tableau 1 Onglets Mixtes Réglage DU Biseau Type DE CoupeAutre méthode de coupe de corniche Coupe de l’aluminiumMatériau arqué Matériau largeGarantie complète EntretienDewalt DEWALT...PARA Trabajos PesadosContenido Instrucciones importantes de seguridad Doble aislamientoClavijas polarizadas DW705 Instrucciones de seguridad para todas las herramientasCalibre mínimo requerido AWG para cables de extensión Instrucciones de seguridad adicionales para ingleteadorasMás No más Calibre promedio del alambre Desempaque su ingleteadora Conexión eléctricaFamiliarícese con su sierra Montaje en banco AccesoriosTope DE Longitud Ajustable DW7051 Instalación del disco Fig Extensión lateral de la mesa para algunos modelosAjuste de la guarda inferior trasera Corte de la placa de respaldoTransporte de la sierra AjustesApague LA Sierra Antes DE Realizar Cualquier Ajuste Ajuste DE LA Escala DEL IngleteAjuste DEL Indicador DE LA Escala Ajuste a Escuadra DEL Ángulo DE Corte DEL DiscoIndicador DEL Ángulo DE Corte Tope DEL BiselCarbones OperaciónInterruptor Cortes CON SU SierraCalidad DEL Corte Cortes DE BiselPosicion DE Cuerpo Y Manos VER Figura Sujecion DE LA Pieza DE Trabajo Apague y desconecte la sierraSoporte Para Piezas Largas Corte DE MARCOS, CAJAS, Y Otros Proyectos DE Cuatro LadosCorte DE Inglete Compuesto Escala Doble DE IngleteEscala Vernier Corte DE Inglete a LA DerechaEsquina Exterior Lado DerechoCorte DE Molduras DE Remate Ajuste DE Bisel Tipo DE Corte Metodo Alternativo Para Cortar Molduras DE RemateMantenimiento ImportanteCorte de aluminio Material arqueadoGuía para la solución de problemas frecuentes Garantía Completa