Black & Decker 489051-00 Operation, Starting and Stopping SAW, Locking Switch in the OFF Position

Page 15

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING SAW

The on/off switch (A) Fig. 27 is located on the front of the saw cabinet. To turn the saw “ON”, move the switch (A) up to the “ON” position. To turn the saw “OFF”, move the switch (A) down to the “OFF” position.

MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. IN THE EVENT OF A POWER FAILURE, MOVE THE SWITCH TO THE “OFF” POSITION. AN ACCIDENTAL START-UP CAN CAUSE INJURY.

LOCKING SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. To lock the tool, grasp the switch toggle (B) and pull it out of the switch (Fig. 28). With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed while the saw is running, the machine can be turned “OFF,” but cannot be restarted without re-inserting the switch toggle (B).

A

Fig. 27

C

B

Fig. 28

OVERLOAD PROTECTION

Your saw is equipped with a reset button (C) Fig. 28. If the motor stops or fails to start due to over-loading (cutting stock too fast, using a dull blade, using the saw beyond its capacity, etc.) or low voltage, turn the switch to the “OFF” position. Let the motor cool three to five minutes. Push the reset button (C) to reset the overload device. The motor can then be started again in the usual manner.

BLADE HEIGHT ADJUSTMENT

To adjust the height of the saw blade, turn the handwheel (A) Fig. 29. Turning the handwheel clockwise lowers the blade and turning the handwheel counter- clockwise raises the blade.

A

Fig. 29

15

Image 15
Contents Before Returning this Product For ANY Reason Please Call BDTS100 10 254MM Table SAWTable of Contents Important Safety InstructionsSafety Guidelines Definitions California Proposition USE of this Tool can Generate General Safety RulesFailure to Follow These Rules MAY Result in Serious Injury Additional Safety Rules for Table SawsPower Connections Motor SpecificationsGrounding Instructions Functional Description Carton ContentsParts Elevating and Supporting Surfaces for a SAW with no Stand AssemblyUnpacking and Cleaning Assembly Tools RequiredSAW to Stand Assembling StandAttaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Attaching Miter Gauge Holder Miter GaugeIllustrates the miter gauge D inserted into the holder Assembling RIP FenceStarting and Stopping SAW Locking Switch in the OFF PositionBlade Height Adjustment OperationBlade Tilt Adjustment 45 Degree Positive Stop AdjustmentsTo Adjust Positive Stop AT 45 Degrees Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeConstructing a Push Stick RippingAccessory Dado Cutterhead Using Auxiliary Wood Facing on RIP FenceDado Head SET Table Insert Constructing a Push Stick PushstickConstructing a Featherboard Troubleshooting MaintenanceBanc DE Scie BDTS100 254 MM 10 PO Proposition 65 DE LA Californie Table DES MatièresDirectives DE Sécurité Importantes Lignes Directrices EN Matière DE Sécurité DéfinitionsDirectives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Supplémentaires Pour LES Bancs DE ScieConnexions Électriques Caractéristiques Techniques DU MoteurDirectives DE Mise À LA Terre AVANT-PROPOS Rallonges ÉlectriquesDescription Fonctionnelle Contenu DU CartonAssemblage Désemballage ET NettoyageOutils Nécessaires Pour L’ASSEMBLAGE Fixation DE L’ENSEMBLE PARE-MAIN/COUTEAU Séparateur Assemblage DU SocleScie SUR Socle Fixation DU Volant Servant À Régler LA Hauteur DE LA LameAssemblage DU Guide Longitudinal FonctionnementJauge À Onglet Fixation DU Support DE LA Jauge À OngletRéglage DE L’INCLINAISON DE LA Lame Verrouiller L’INTERRUPTEUR EN Position D’ARRETProtection Contre LES Surcharges Réglage DE LA Hauteur DE LA LameRéglage DE Linsert DE Table Utilisation DE LA Jauge À Onglet ET RéglagesChangement DE LA Lame Sciage EN Long TronçonnageFraise Accessoire À Rainurer Entretien Construire UN PoussoirConstruire UNE Planche EN Éventail Quel EST LE Problème ? QUE FAIRE… Dépannage555326-7100 LA Propuesta 65 DE California ÍndiceInstrucciones Importantes Sobre Seguridad Normas DE Seguridad DefinicionesInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadMantenga LOS BRAZOS, LAS Manos y LOS Dedos lejos de la hoja Normas DE Seguridad Adicionales Para LAS Sierras DE MesaConexiones Eléctricas Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Introducción Descripción DE LAS FuncionesContenido DE LA Caja Cables ProlongadoresSuperficies DE Apoyo Y Elevación Para UNA Sierra SIN Base MontajeDesembalaje Y Limpieza Herramientas Necesarias Para EL MontajeMontaje DE LA Base Sierra a LA BaseColocación DEL Volante Para Ajustar LA Altura DE LA Hoja Colocación DEL Ensamble DE Guarda DE LA Hoja Y Hedidor Calibrador DE IngleteColocación DEL Sujetador DEL Calibrador DE Inglete Operación Ajustar UN Tope Positivo a 45 Grados Ajustes DE Topes Positivos a 90 Y 45 GradosOperación DE LA Guía DE Corte Y Ajustes Ajuste DEL Inserto Para MesaCambio DE LA Hoja Operación DEL Calibrador DE Inglete Y AjustesCorte Transversal Corte LongitudinalVara Para Empujar Cabezal Portacuchilla Accesorio Para Ranuras Construcción DE UN Palo DE EmpujarConstrucción DE UNA Tabla DE Canto Biselado Mantenimiento Detección DE ProblemasPara Otras Localidades Llame AL 55 5326 Información de mantenimiento