Graco 3A0868G important safety instructions Configure 1-4 Screens, Confirm Change of System Type

Page 43

Setup Mode Details

Configure 1-4 (Screens 18-21)

Configure 1 (Screen 18) displays if is selected on Setup Home (Screen 17). This screen allows users to set up the system type (pump or meter) and number of guns (1 or 2).

NOTE: If 1 gun is selected, users can enable a gun flush box (✓=yes; X=no). The gun flush box option is avail- able only for 1-gun systems.

For all pump systems, the type of dosing is dynamic, and the number of colors is 1. See Dynamic DosingDy- namic Dosing, page 48, for more information.

FIG. 37. Confirm Change of System Type

Configure 2 (Screen 19) allows users to set for each gun the hose length (0.1 to 45.7 m, 0.3 to 150 ft) and hose diameter (0.1 to 1 inch). The system uses this informa- tion to calculate pot life volume. The pot life volume tells the system how much material must be moved to trigger a reset of the pot life timer. It also tells the system the

System type

Gun flush box

Number of guns

volume needed to fill during a load sequence.

Users also can configure the flow rate region and the air flow switch. The flow rate region (High/Low) determines the sensitivity of the overdose alarm:

Home

FIG. 36. Configure 1 (Screen 18)

•Press to highlight the desired field. Press

to display the dropdown menu for that field.

Press to choose from the menu options and

to set. Press to move to the next field.

•Press to move through Configure 2 (Screen 19), Configure 3 (Screen 20), and Configure 4 (Screen 21).

NOTE: If you change system type (pump to meter) or number of guns, a verification screen appears. Use

to highlight and press on the to make the change, or on the to return to Configure 1 (Screen

18)without making a change. If a change is made, the system locks so that you cannot spray or mix. Power down and power back up again to clear the lock and put the new settings into effect. The lock ensures that the selection was intended, and prevents the user from attempting to operate with incorrect settings.

•Select the High setting if your flow rate is 250 cc/min or higher. The High setting has a 100cc over- dose volume.

•Select the Low setting if your flow rate is less than 250 cc/min. The Low setting has a 50 cc over- dose volume.

The air flow switch can be disabled here for airless applications. Select to enable or to disable.

A change in any of these fields will trigger the lock. See NOTE in previous paragraph.

Gun 1

Gun 2

hose

hose

length

length

 

Gun 1

Gun 2

hose

hose

diameter

diameter

Air

Flow rate

flow

region

switch

 

Home

FIG. 38. Configure 2 (Screen 19)

Configure 3 (Screen 20) allows users to set preferred language (for optional USB Module), date format, date, time, password (0000 to 9999), and number of minutes (0 to 99) of inactivity required before the backlight turns off. Configure 4 (Screen 21) allows users to set pre- ferred units for distance, volume, and pressure.

3A0868G

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents ProMix 2KE Contents USB ModelsSeries Ratio Pumps Psi MPa, bar Port Approvals Models Related ManualsManual Description Special Conditions for Safe USE Fire and Explosion HazardElectric Shock Hazard Skin Injection Hazard Intrinsic SafetyPersonal Protective Equipment Equipment Misuse HazardMoving Parts Hazard Toxic Fluid or Fumes HazardImportant Two-Component Material Information Glossary of Terms Component Identification and Definition InstallationOverview UsageHazardous Location Installation Intrinsically Safe Installation RequirementsNon-Hazardous Locations Air regulator and bleed-type shutoff valve Display ModuleAir Supply RequirementsAir Connections Fluid SupplyFluid Connections Key SVA DVASVB DVB Used only on is models Tubing Chart and DiagramsGFB1-A ATOM-1 ATOM-2 Electrical Power Connection non-IS units onlyGrounding Grounding Key Function Display ModuleDisplay IG . Display ModuleIcon Key Screen Summary Run ModeSetup Mode TroubleshootingRanges for User Inputs Screen User Input Range/Options DefaultRun ErrorsPump Control HomeRecipe Set-Up Home Password ConfigureCalibration Set-Up Home MaintenanceSystem Outputs System Outputs Set-Up Home System InputsMembrane Test Pre-Operation Tasks Power OnInitial System Setup Basic OperationPrime the System Calibrate the pump Pump CalibrationPurging Mixed Material Purging Fluid Supply System SprayingPurging Bration 1 and 2 Screens 22 and 23,Purging Fluid Supply System Purging Mixed MaterialSolenoid Valves in Control Box Shutdown Pressure Relief ProcedureValve Settings Lock ModeJob Log Error LogUse of Optional USB Module USB LogsSample Error Log SetupRecommended USB Flash Drives Download ProcedureUSB Port Run Mix Batch Screen Run Mode DetailsRun Mix Spray Screen Run Home ScreenRun Mix Totals Screen Run Log Errors ScreensRun Job Number Screen Run Pump Control Screen Run Pump Control ScreenPassword Screen Setup Mode DetailsSetup Home Screen Confirm Change of System Type Configure 1-4 ScreensRecipe 1-1 Screen Recipe 1-2 Screen Configure 3 Screen 20 and Configure 4 ScreenComponent Frequency Maintenance 1-3 ScreensMaintenance Recommendations Recommended MaintenanceCalibration 1 and 2 Screens 22 Troubleshooting ScreensTroubleshooting System Outputs Screen Troubleshooting System Inputs ScreenMembrane Test Screen General Operating Cycle, Dynamic Dosing Dynamic DosingSelect a Component B Restrictor Size B Control Range with Properly Sized Restrictor Pressure Too High Pressure Too Low Pressure B PressureAir Flow Switch AFS Function System ErrorsSystem Alarms To Clear Error and RestartSystem Idle Warning Idle System Alarm/Advisory/Record Codes Error CodesUSB Communication Error Alarm TroubleshootingAlarm and Description Cause Solution Communication ErrorEQU2 PreFill Error Alarm and Description Cause Solution SFA1 or SFB1PreMix Error Pneumatic Schematic, page 66 orAlready about equal, verify that com Ratio Low ErrorQDB1 QDA1Linear Sensor Error Alarm and Description Cause Solution QTA1 or QTB1Dose Time Error Leak ErrorStall Up Error Alarm and Description Cause Solution DDA1 or DDB1Diving/Cavitation Error Park ErrorExample Dynamic Dosing Restrictor Selection GraphsRestrictor Sizes Size Code Orifice Size Flow Rate cc/min Detail View Differential Pressure between a and B500 1000 1500 2000 2500 3000 3500 4000 200 14 150 10 100 7 50 3.4 500 1000 Psi 40 2.8 30 2.1 20 1.4 10 0.7 500 1000 System Pneumatic Schematic SchematicsNon-Hazardous Location Pneumatic SchematicAIR Flow Switch SIG Fluid J4CONTROL Module Hazardous Location Electrical SchematicPower Supply Non-Hazardous Electrical Schematic Merkur Merkur Bellows Dimensions and MountingNoise level Technical DataProMix 2KE Metric On-ratio accuracyGraco Information Graco Standard Warranty
Top Page Image Contents