Bostitch BTFP02006 instruction manual Code Possible cause, Solution. Do Not Overtighten

Page 19


Air leaks from safety valve			6
Knocking Noise			6,16,17
Pressure reading on the regulated pressure gauge drops when an accessory is used....7
Compressor is not supplying enough air to operate accessories			....................8,9,10,11,12,15
Regulator knob has continuous air leak			13
Regulator will not shut off air outlet			13
Moisture in pump crankcase			14,18
Motor will not run			11,19,20,21,22,23,24,25,26
	Troubleshooting Codes
Code	possible cause	POSSIBLE SOLUTION

1Pressure switch does not Set the On/Off switch to OFF, if the unit shut off motor when com- does not shut off contact an authorized pressor reaches cut-out service center.

pressure

2	Pressure switch cut-out too	Contact an authorized service center.
	high
3	Tube fittings are not tight	Tighten fittings where air can be heard
	enough	escaping. Check fittings with soapy water
		solution. Do Not Overtighten.
4	Defective air tank	Air tank must be replaced. Do not repair the
		leak.
					Risk of bursting. Do not drill into,
					Risk of bursting. Do not drill into,
		weld or otherwise modify air tank or it will
		weaken. The air tank can rupture or explode.
5	Leaking seals	Contact an authorized service center.

6	Defective safety valve	Operate safety valve manually by pulling on
		ring. If valve still leaks, it must be replaced.
7	Regulator is not adjusted	It is normal for some pressure drop to occur
	correctly for accessory	when an accessory is used, adjust the regulator
	being used	as instructed in Regulator under Features if
		pressure drop is excessive.
		NOTE: Adjust the regulated pressure under
		flow conditions while accessory is being used.
8	Prolonged excessive use	Decrease amount of air usage.
	of air
9	Compressor is not large	Check the accessory air requirement. If it is
	enough for accessory	higher than the SCFM or pressure supplied by
		air compressor, a larger compressor is needed
		to operate accessory.
10	Hole in air hose	Replace air hose.

11	Check valve restricted	Remove, clean or replace.

12	Air leaks	Tighten fittings.

13	Regulator is damaged	Replace.

14Unit operating in damp or Move unit to a dry well ventilated area humid conditions

15

Restricted air intake filter

Clean or replace air intake filter

19

Image 19

Contents Guide Dutilisation Manual DE Instrucciones Property damage What can happen Risk of explosion or fire How to prevent itNever place objects against or on top of compressor Risk of Bursting What can happen How to prevent itAttachments & accessories Risk to Breathing Asphyxiation What can happenAlways wear certified safety equipment Risk from Flying Objects How to prevent itTires Never stand on the compressor Risk of Hot surfaces How to prevent itRisk from Moving Parts How to prevent it Risk of Unsafe Operation How to prevent itRisk from Noise Risk of FallingHot Surfaces Air Intake Filter Save These Instructions for Future USEHandle Features Fig Assembly InstallationGrounding Instructions Installing HosesDisconnecting Hoses Lubrication and OilCompatibility Pre-Start Checklist FigPreparation For Use Voltage and Circuit ProtectionStart-up Fig Operating ProceduresBreak-in Procedure Initial Set-up FigLifting MaintenanceStorage and Transporting TransportingEasier Maintenance ChartChecking Safety Valve Fig Checking Air Filter Element FigChecking oil Valve can then be removed, cleaned and reinstalledDraining Air Tank Fig Compressor Pump Oil FigRepairs AccessoriesService Information Full One Year WarrantyProblem Code Troubleshooting GuideGlossary Code Possible cause Solution. Do Not OvertightenWeld or otherwise modify air tank or it will See Motor Overload under Features Possible SolutionSee Extension Cords under Installation Pourrait se solder par des blessures mineures ou modérées Définitions lignes directrices en matière de sécuritéConserver ces directives La mort ou des blessures gravesComment l’Éviter Risque Repiratoire AsphyxieRisque d’Éclatement Votre compresseur d’air est alimenté Accessoires Pneus Risque de choc Électrique ÉlectricitÉRisque Provenant DES Objets Projetés EN L’AIR Risque associÉ au bruit Remarques À propos du bruit EmplacementInstaller un extincteur dans la zone de travail Risque DE ChuteSurfaces chaudes Fiche techniqueFiltre dadmission dair L Poignée Pressostat Jauge dhuile de la pompeCaractÉristiques Fig SystÈme de refroidissement non illustré Manomètre de pression réguléeRÉgulateur Robinet de purgeDÉconnexion des tuyaux Installation des rouesAssemblage Raccordement des tuyauxLa terre Q Directives relatives à la mise à la terreRallonges Protection de la tension et du circuitCompatibilité Mode d’emploiListe de vérification de pré-démarrage Fig Démarrage Fig Procédures de fonctionnementRéglage initial Fig Procédure de rodageLevage Rangement ET TransportEntretien TransportVérification de la soupape de sûreté Fig Programme d’entretienFermer la soupape de purge dès la fin de l’opération Vérification des éléments du filtre d’air FigVidange du réservoir d’air Fig Huile de la pompe du compresseur FigFecha y lugar de compra Accesorios100/SAE40, huile non-détergente et suivez les Étapes 4 Vidange d’huileEsta garantía no será válida en los siguientes casos Póliza de GarantíaGarantía completa de un año Calificado. Utilice siempre piezas de repuesto idénticasProblème Code Obtenir le remplacement gratuitGlossaire Guide de dépannage’air, ni le souder ou Solution ProbableCodes de dépannage Code Cause possible’enclenchement InstallationCause possible CaractéristiquesRiesgo de explosión o incendio Guarde estas instruccionesSiempre apague y desenchufe la unidad cuando no esté en uso Riesgo Respiratorio asfixiaRiesgo de explosión Nunca coloque objetos contra o sobre el compresorReemplácelo con un tanque de aire nuevo Modificaciones o intento de reparación del tanque de aireElementos y accesorios NeumáticosInstalación Riesgo de descarga eléctricaRiesgo de objetos despedidos Riesgo DE superficies calientesRiesgo por piezas móviles Riesgo de operación inseguraRiesgo por ruidos EspecificacionesMinutos Apagado Superficies calientesTipo DE Conexión Rápida E Ciclo DE TrabajoCaracterísticas Fig Válvula de seguridad Interruptor de Encendido/ApagadoInterruptor de presión Válvula aliviadora de presión no se muestraProtector DE Sobrecarga DEL Motor no se muestra Válvula de drenajeSistema de enfriamiento no se muestra Bomba del compresor de aireEnsamblaje InstalaciónVoltaje y protección del circuito Cables prolongadoresLugar Configuración inicial FigPreparación para el uso CompatibilidadApagado Fig Procedimientos operativosAlmacenamiento Y Transporte Puesta en marcha FigLeva ntar la unidad MantenimientoConsideraciones sobre el ruido TransporteControlar la válvula de seguridad Fig Tabla de mantenimientoControlar el elemento del filtro de aire Fig Controlar el aceite Drenar el tanque de aire FigAceite de la bomba del compresor Fig El mantenimientoInformación del servicio técnico AccesoriosCambio de aceite Reparaciones Glosario Guía de detección de problemasNi modifique el Códigos de detección de problemasCódigo causa posible Solución PosibleInstalación De servicio de fábrica Tor de presiónColoque el interruptor Encendido Sión del interruptor de presión