DeWalt JT360 instruction manual Adjusting Table Gibs, Fence Operation

Page 18

ADJUSTING TABLE GIBS

"Gibs" are provided to take up all play between the mating dovetail ways of the base and the infeed and outfeed tables. The "gib" for the infeed table is shown at (A) Fig. 46, and the "gib" for the outfeed table is shown at (B) Fig.

47.Proper "gib" adjustment is necessary for the correct functioning of the jointer. The "gibs" were adjusted at the factory and should require no further adjustment. If it becomes necessary to adjust the "gibs", proceed as follows:

1.To adjust the infeed or outfeed table "gibs," loosen three locknuts (F) Fig. 46, for the infeed table or two locknuts (G) Fig. 47, for the outfeed table. For the infeed table, make sure the table locking lever is loose . For the outfeed table, make sure the table locking screw (E) Fig. 47, is loose.

2.Tighten or loosen three gib adjustment screws (C) Fig. 46, as necessary for the infeed table or two gib adjustment screws (D) Fig. 47, as necessary for the outfeed table; starting with the lower screw first and as you proceed to the top screw, gently raise the outboard edge of the table that is being adjusted. This will offset any tendency for the table casting to "droop or sag" and permit the gib to be adjusted to a secure fit. After the gibs have been adjusted, tighten locknuts (F) Fig. 46, (G) Fig. 47, table locking screw

(E) Fig. 47, and infeed table locking lever.

IMPORTANT: Do not leave the adjusting screws too loose. It should take a little bit of effort to move the tables up or down. Jointers are finishing machines and you can’t expect proper accuracy or finish if the tables are not set properly.

FENCE OPERATION

The fence can be moved across the table and can tilt 45 degrees right or left at any position on the table as follows:

1.To move the fence across the table, loosen lock handle (A) Fig. 48, slide fence to the desired position on the table and tighten lockhandle (A). As the fence is moved across the table, the rear cutterhead guard

(B)covers and guards the cutterhead in back of the fence. NOTE: Lock handle (A) is spring-loaded and can be repositioned by pulling up on the handle and repositioning it on the serrated nut located underneath the hub of the handle.

2.To tilt the fence to the right or left loosen lock handle (C) Fig. 49, and pull out and turn plunger

(D)to release the positive stop. A tilting lever (E) is provided on the back of the fence to assist in tilting the fence. NOTE: Lock handle (C) is spring-loaded and can be repositioned by pulling out the handle and repositioning it on the serrated nut located underneath the hub of the handle.

3.Tilt the fence to the desired angle, in or out, and tighten lock handle (C) Fig. 49. IMPORTANT: When cutting bevels and the angle is small there is little difference whether the fence is tilted in or out; however, at angles approaching 45 degrees it may become difficult to hold the work securely against the fence when the fence is tilted out. In these cases we suggest that the fence be tilted toward the table, as shown in Fig. 49. The fence will form a V-shape with the tables and the work is easily pressed into the pocket while passing across the knives.

Fig. 46

F

C

F

C

A

Fig. 47

D G

E G

D

B

Fig. 48

B A

Fig. 49

C

 

D

E

18 - English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Canteador de 152 mm 6 pulg con base Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEAdditional Specific Safety Rules Refer to them often and use them to instruct othersPower Connections Motor SpecificationsGrounding Instructions Volt Single Phase Operation Extension CordsCarton Contents Functional DescriptionUnpacking and Cleaning Jointer PartsMotor and Switch to Stand AssemblyAssembly Tools Required StandJointer to Stand English Infeed Table Adjustment Handle Dust Chute CoverDust Collector Adapter Motor Pulley BELT, Aligning PULLEYS, Adjusting Belt TensionPULLEYS, and Adjusting Belt Tension Motor Pulley and Belt GuardFence Cutterhead GuardOperation Locking Switch in the OFF PositionInfeed Table Adjustments Starting and Stopping JointerOutfeed Table Adjustments Knife and Outfeed Table AdjustmentsInfeed Table Positive Stops SET TOO LOW Knivescutter SET TOO HighKnives Knives ATAdjusting Table Gibs Fence OperationAdjusting Fence Positive Stops Index collar and loosen fence lockingAdjusting Fence Guards Replacing and Resetting KnivesPlacement of Hands During Feeding Machine USEDefinitions of Jointing and Planing Operations Jointing AN EdgeTaper Cuts Planing or SurfacingBeveling Cutting a RabbetPlaning Short or Thin Work TroubleshootingPlaning Warped Pieces Direction of GrainWhetting Knives MaintenanceService Removing Dust Chute CoverFree Warning Label Replacement AccessoriesWarranty Service and RepairsConservez CES Instructions LES Instructions Importantes DE SureteMesures DE Sécurité Définitions LA Proposition DE CalifornieRègles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES InstructionsRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsDescription Fonctionnelle Contenus DE BoiteAVANT-PROPOS Composantes DE LA Dégauchisseuse Déballage ET NettoyageSocle AssemblageOutils Requis Pour L’ASSEMBLAGE Goulotte DE Poussière AU SocleMoteur ET Interrupteur AU Socle Dégauchisseuse SUR LE SocleFrançais Poignée DE Réglage DE LA Table Dentrée Couvercle DE Goulotte DE PoussièreAdaptateur DU Collecteur DE Poussière Poulie Motrice Alignement DES Poulies ET Réglage DE LA Tension DE CourroiePoulie Motrice ET Garde Protecteur DE Courroie GuideDES Poulies ET Réglage DE Tension DE Courroie Fonctionnement Démarrage ET Arrêt DE LA DégauchisseuseVerrouillage DE L’INTERRUPTEUR EN Position Arrêt Réglages DE LA Table Dentrée Butées Fixes DE LA Table DentréeRéglages DE LA Table DE Sortie Réglages DE LA Table DE Sortie ET DE LA Fraise Coupante Débranchez la machine de la source d’alimentationRéglage DES Glissières DE Table Fonctionnement DES GuidesRéglage DES Butées Fixes DE Guide Remplacement ET Repositionnement DES Couteaux Réglage DES Gardes DU GuideDES Précautions Doivent Emplacement DES Mains Durant Lacheminement Utilisation DE LA MachineDéfinition DES Opérations DE Jointage ET DE Rabotage Jointer UN BordDécoupes Coniques Rabotage OU ResurfaçageBiseautage Couper UNE FeuillureRabotage Douvrages Courts OU Minces DepannageRabotage DE Pièces Voilées Direction DU GrainEntretien Garantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationProposición DE California Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Guarde Estas InstruccionesNormas Generales DE Seguridad Puede Generar Y DispersarNormas Específicas Adicionales DE Seguridad Guarde Estas InstruccionesConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Cordones DE Extensión Operación DE UNA Sola Fase CON 240 VoltiosDescripción Funcional Contenido DE CartonPrologo Desempaquetado Y Limpieza EnsamblajePiezas DE LA Canteador Estimación DEL Tiempo DE Ensamblaje 2-3 HorasMontaje DEL Estante Montaje DEL Conducto DE Polvo AL EstanteMontaje DEL Motor E Interruptor AL Estante Colocar LA Canteador EN LA Base Montaje DE LA Tapadera DEL Conducto DE Polvo Montaje DEL Adaptador DEL Recolector DE Polvo Montaje DE LA Polea DEL MotorMontaje DEL Protector DE Polea DEL Motor Y DE LA Correa Montaje DE LA GuiaMontaje DEL Protector DEL Cabezal DE Corte OperaciónBloqueando EL Interruptor EN LA Posicion DE Apagado Arrancando Y Deteniendo LA CanteadorAjustes DE LA Mesa DE Alimentacion Topes Positivos DE LA Mesa DE AlimentacionAjustes DE LA Mesa DE Avance DE Salida Ajustes DE LAS Cuchillas Y DE LA Mesa DE Avance DE Salida Desconecte la maquina de la fuente de energiaAjuste DE LAS Correderas DE LA Mesa Funcionamiento DE LA GuiaAjustando LOS Topes Positivos DE LA Guia Ajuste DE LOS Protectores DE LA Guia EXTRACCION, REEMPLAZO, Y Reajuste DE LAS CuchillasUtilizar LA Maquina Colocación DE LAS Manos Durante LA AlimentacionCorrecto Incorrecto Dimensiones Minimas DE Canteador Definiciones DE LAS Funciones DE Canteador Y AcepilladoCanteador UN Borde Cortes Conicos Acepillado O AlisadoBiselado Corte DE AlefrizCanteador DE Materiales Cortos O Delgados Localizacion DE FallasAcepillado DE Materiales Alabeados Direccion DEL GranoMantenimiento ServicioAccesorios GarantiaPóliza DE Garantía Identificación Delproducto
Top Page Image Contents