DeWalt JT360 instruction manual Maintenance, Service, Whetting Knives, Removing Dust Chute Cover

Page 25

MAINTENANCE

After considerable use, the knives will become dull and it will not be possible to do accurate work. Unless badly damaged by running into metal or other hard material, the knives may be sharpened as follows:

WHETTING KNIVES

Disconnect machine from power source.

Use a fine carborundum stone, cover it partly with paper as indicated in Fig. 74 to avoid marking the table. Lay the stone on the infeed table, lower the table and turn the cutterhead forward until the stone lies flat on the bevel of the knife as shown. Hold the cutterhead from turning, and whet the beveled edge of the knife, stroking lengthwise by sliding the stone back and forth across the table. Do the same amount of whetting on each of the three knives.

REMOVING DUST CHUTE COVER

The dust chute cover (A) Fig. 75, can be removed, for cleaning purposes, by removing the two wing screws

(B).

Make certain the machine is disconnected from the power source before removing the dust chute cover. The dust chute cover (A) must always be assembled to the dust chute during operation.

 

 

 

 

 

 

 

 

Fig. 74

 

OILSTONE PARTLY

 

 

 

 

 

 

 

 

 

 

COVERED WITH PAPER

 

 

OUT-FEED

IN-FEED TABLE

 

 

TABLE

 

 

 

 

 

 

 

 

CUTTER

 

 

 

 

 

WHETTING KNIVES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig.75

 

 

 

B

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION & RUST PROTECTION

Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.

To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand Pad, a can of WD-40®and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad. Degrease the table, then apply the protective product as described above.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery.com. You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to receive personalized support from highly-trained technicians.

25 - English

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Canteador de 152 mm 6 pulg con base Important Safety Instructions Table of ContentsSafety Guidelines Definitions Stay ALERT, Watch What YOU are DOING, and USE General Safety RulesRefer to them often and use them to instruct others Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Extension Cords Volt Single Phase OperationFunctional Description Carton ContentsJointer Parts Unpacking and CleaningAssembly Tools Required AssemblyMotor and Switch to Stand StandJointer to Stand English Dust Chute Cover Infeed Table Adjustment HandleDust Collector Adapter PULLEYS, and Adjusting Belt Tension BELT, Aligning PULLEYS, Adjusting Belt TensionMotor Pulley Motor Pulley and Belt GuardCutterhead Guard FenceInfeed Table Adjustments Locking Switch in the OFF PositionOperation Starting and Stopping JointerKnife and Outfeed Table Adjustments Outfeed Table AdjustmentsInfeed Table Positive Stops Knives Knivescutter SET TOO HighSET TOO LOW Knives ATFence Operation Adjusting Table GibsIndex collar and loosen fence locking Adjusting Fence Positive StopsReplacing and Resetting Knives Adjusting Fence GuardsMachine USE Placement of Hands During FeedingJointing AN Edge Definitions of Jointing and Planing OperationsBeveling Planing or SurfacingTaper Cuts Cutting a RabbetPlaning Warped Pieces TroubleshootingPlaning Short or Thin Work Direction of GrainService MaintenanceWhetting Knives Removing Dust Chute CoverWarranty AccessoriesFree Warning Label Replacement Service and RepairsMesures DE Sécurité Définitions LES Instructions Importantes DE SureteConservez CES Instructions LA Proposition DE CalifornieLutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Instructions Règles Spécifiques Additionnelles DE SûretéSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Fonctionnement Monophasé À 240 Volts Cordon DE RallongeContenus DE Boite Description FonctionnelleAVANT-PROPOS Déballage ET Nettoyage Composantes DE LA DégauchisseuseOutils Requis Pour L’ASSEMBLAGE AssemblageSocle Goulotte DE Poussière AU SocleDégauchisseuse SUR LE Socle Moteur ET Interrupteur AU SocleFrançais Couvercle DE Goulotte DE Poussière Poignée DE Réglage DE LA Table DentréeAdaptateur DU Collecteur DE Poussière Alignement DES Poulies ET Réglage DE LA Tension DE Courroie Poulie MotriceGuide Poulie Motrice ET Garde Protecteur DE CourroieDES Poulies ET Réglage DE Tension DE Courroie Démarrage ET Arrêt DE LA Dégauchisseuse FonctionnementVerrouillage DE L’INTERRUPTEUR EN Position Arrêt Butées Fixes DE LA Table Dentrée Réglages DE LA Table DentréeRéglages DE LA Table DE Sortie Débranchez la machine de la source d’alimentation Réglages DE LA Table DE Sortie ET DE LA Fraise CoupanteFonctionnement DES Guides Réglage DES Glissières DE TableRéglage DES Butées Fixes DE Guide Réglage DES Gardes DU Guide Remplacement ET Repositionnement DES CouteauxDES Précautions Doivent Utilisation DE LA Machine Emplacement DES Mains Durant LacheminementJointer UN Bord Définition DES Opérations DE Jointage ET DE RabotageBiseautage Rabotage OU ResurfaçageDécoupes Coniques Couper UNE FeuillureRabotage DE Pièces Voilées DepannageRabotage Douvrages Courts OU Minces Direction DU GrainEntretien Remplacement Gratuit DE Létiquette AccessoiriesGarantie Entretien ET RéparationPautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesProposición DE California Guarde Estas InstruccionesPuede Generar Y Dispersar Normas Generales DE SeguridadGuarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadEspecificaciones DEL Motor Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Operación DE UNA Sola Fase CON 240 Voltios Cordones DE ExtensiónContenido DE Carton Descripción FuncionalPrologo Piezas DE LA Canteador EnsamblajeDesempaquetado Y Limpieza Estimación DEL Tiempo DE Ensamblaje 2-3 HorasMontaje DEL Conducto DE Polvo AL Estante Montaje DEL EstanteMontaje DEL Motor E Interruptor AL Estante Colocar LA Canteador EN LA Base Montaje DE LA Tapadera DEL Conducto DE Polvo Montaje DE LA Polea DEL Motor Montaje DEL Adaptador DEL Recolector DE PolvoMontaje DE LA Guia Montaje DEL Protector DE Polea DEL Motor Y DE LA CorreaBloqueando EL Interruptor EN LA Posicion DE Apagado OperaciónMontaje DEL Protector DEL Cabezal DE Corte Arrancando Y Deteniendo LA CanteadorTopes Positivos DE LA Mesa DE Alimentacion Ajustes DE LA Mesa DE AlimentacionAjustes DE LA Mesa DE Avance DE Salida Desconecte la maquina de la fuente de energia Ajustes DE LAS Cuchillas Y DE LA Mesa DE Avance DE SalidaFuncionamiento DE LA Guia Ajuste DE LAS Correderas DE LA MesaAjustando LOS Topes Positivos DE LA Guia EXTRACCION, REEMPLAZO, Y Reajuste DE LAS Cuchillas Ajuste DE LOS Protectores DE LA GuiaColocación DE LAS Manos Durante LA Alimentacion Utilizar LA MaquinaCorrecto Incorrecto Definiciones DE LAS Funciones DE Canteador Y Acepillado Dimensiones Minimas DE CanteadorCanteador UN Borde Biselado Acepillado O AlisadoCortes Conicos Corte DE AlefrizAcepillado DE Materiales Alabeados Localizacion DE FallasCanteador DE Materiales Cortos O Delgados Direccion DEL GranoServicio MantenimientoGarantia AccesoriosIdentificación Delproducto Póliza DE Garantía
Top Page Image Contents