DeWalt DW621 manual Instructions for use

Page 25

E N G L I S H

Adjusting the depth of cut (fig. D)

Your router is equipped with a high precision depth adjustment system including a zero reset ring for both the quick adjuster and the fine adjuster.

Quick adjustment using the graduation with zero reset ring

•Loosen the depth stop locking bolt (14).

•Unlock the plunge limiter (15) by turning it counterclockwise.

•Lower the router carriage until the cutter is in contact with the workpiece.

•Tighten the plunge limiter (15).

•Set the quick adjuster (16) to zero using the ring (22). The depth stop (13) must be in contact with the revolver depth stop (12).

•Adjust the depth of cut using the quick adjuster (16) and the corresponding graduation. The adjusted depth of cut is indicated by the arrows (23).

•Tighten the depth stop locking bolt (14).

Triple depth adjustment using the revolver depth stop

The revolver depth stop (12) can be used to set

3 different depths. This is particularly useful for deep cuts, performed in steps.

•Place a depth template between the depth stop (13) and the revolver depth stop (12) to adjust the exact cutting depth.

•If required, set all three screws.

Fine adjustment

When not using a depth template, or if the depth of cut needs readjustment, it is recommended to use the fine adjuster (17).

•Adjust the depth of cut as described above.

•Set the fine adjuster to zero using the ring (24).

•Rotate the fine adjuster (17) to the required position: one turn corresponds to approximately 1 mm and 1 mark to 0.1 mm.

Depth adjustment with router installed in inverted position (fig. D)

•Remove the depth stop (13) and replace it with the depth stop (DE6956) available as an option.

•Connect the threaded rod of the depth stop (13A) to the revolver depth stop (12).

•Set the depth of cut using the adjuster on the depth stop (13A).

For installing the router in inverted position, refer to the relevant instruction manual on the stationary tool.

Fitting the parallel fence (fig. A & E)

•Fit the guide rods (5) to the router base (10).

•Tighten the locking bolts (9).

•Slide the parallel fence (8) over the rods.

•Tighten the locking bolts (4) temporarily.

•Remove the dust extraction adaptor (18) and close the outlet using the dust extraction plug (25) supplied with the tool.

Adjusting the parallel fence (fig. F)

•Draw a cutting line on the material.

•Lower the router carriage until the cutter is in contact with the workpiece.

•Tighten the plunge limiter (15).

•Position the router on the cutting line.

•Slide the parallel fence (8) against the workpiece and tighten the locking bolts (4).

•Adjust the parallel fence (8) using the fine adjuster

(7). The outer cutting edge of the cutter must coincide with the cutting line.

•Firmly tighten the end lock (20).

Fitting a guide bush (fig. G)

Together with a template, guide bushes play a valuable part in cutting and shaping to a pattern.

•Fit the guide bush (26) to the router base (10) using the screws (27) as shown.

Connecting a dust extractor (fig. A & E)

•Connect a dust extractor hose to the dust extraction adaptor (18) in the router carriage column, or to the dust extraction outlet in the parallel fence (6).

Instructions for use

•Always observe the safety instructions and applicable regulations.

•Always move your router as indicated in fig. H (outer edges/inner edges).

20

en - 5

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DW620 DW621 EÏÏËÓÈη Page Page Page Tillykke Håndoverfræser DW620/DW621Indholdsfortegnelse Tekniske dataSikkerhedsinstruktioner Beskrivelse fig. a Kontroller emballagens indholdYderligere sikkerhedsanvisninger for fræseværktøj Anvendelse af forlængerkabel El-sikkerhedSamling og justering Udskiftning af kabel eller stikSådan monteres parallelanslaget fig. a & E BrugervejledningSådan indstilles parallelanslaget fig. F Tænd og sluk figVedligeholdelse Garanti Herzlichen Glückwunsch Oberfräse DW620/DW621Inhaltsverzeichnis EG-KonformitätserklärungAllgemeines SicherheitshinweiseGerätebeschreibung Abb. a Überprüfen der LieferungKontrollieren Sie Ihr Elektrowerkzeug auf Beschädigungen Zusätzliche Sicherheitshinweise für FräserVerlängerungskabel Elektrische SicherheitZusammenbauen und Einstellen Einstellen des Parallelanschlags Abb. F Montieren des Parallelanschlags Abb. a & EZiehen Sie die Endfixierung 20 fest an Wartung GebrauchsanweisungSchmieren Reinigung der Staubabsaugungssäule Abb. JIhr Elektrowerkzeug erfordert keine zusätzliche Schmierung ReinigungU T S C H Technical data Table of contentsRouter DW620/DW621 CongratulationsKeep work area clean Safety instructionsWear safety goggles GeneralElectrical safety Package contentsMains plug replacement U.K. & Ireland only Description fig. aAssembly and adjustment Using an extension cableReplacing the collet assembly fig. C Inserting and removing a cutter fig. BInstructions for use Maintenance Guarantee ¡Enhorabuena Fresadoras DW620/DW621Contenido Características técnicasGeneralidades Instrucciones de seguridadMantenga limpia el área de trabajo Guarde las herramientas que no utilizaDescripción fig. a Verificación del contenido del embalajeNormas de seguridad adicionales para fresas Utilización de un cable de prolongación Seguridad eléctricaMontaje y ajustes Montaje de la guía rectilínea fig. a & E Instrucciones para el usoAjuste de la guía rectilínea fig. F Mantenimiento Su herramienta eléctrica no requiere lubricación adicional LubricaciónLimpieza Félicitations Defonceuse DW620/DW621Table des matières Caractéristiques techniquesGénéralités Instructions de sécuritéSécurité électrique Contenu de l’emballageDirectives de sécurité additionnelles pour fraises Assemblage et réglage Câbles de rallongeMontage et démontage d’une fraise fig. B Montage du guide parallèle fig. a & E Mode d’emploiRéglage du guide parallèle fig. F Aspiration de poussière fig. a & EEntretien Jours D’ENGAGEMENT Satisfaction Congratulazioni Elettrofresatrice DW620/DW621Indice del contenuto Dati tecniciNorme generali Norme generali di sicurezzaProteggersi da scariche elettriche Descrizione fig. a Contenuto dell’imballoNorme di sicurezza elettrica Norme di sicurezza specifiche per freseAssemblaggio e regolazione Impiego di una prolungaSostituzione del cavo o della spina Inserimento e rimozione di una fresa fig. BMontaggio della squadra laterale fig. a & E Istruzioni per l’usoRegolazione della squadra laterale fig. F Fissaggio del canotto guida fig. GManutenzione Garanzia Utensili inutilizzabili e tutela ambientaleGefeliciteerd Bovenfrees DW620/DW621Inhoudsopgave Technische gegevensAlgemeen VeiligheidsinstructiesBeschrijving fig. a Inhoud van de verpakkingOnderhoud de machine met zorg Extra veiligheidsrichtlijnen voor frezenGebruik van verlengsnoeren Elektrische veiligheidMonteren en instellen Bevestigen van de parallelaanslag fig. a & E Aanwijzingen voor gebruikInstellen van de parallelaanslag fig. F Aansluiten van een stofafzuigsysteem fig. a & EOnderhoud Dagen Niet GOED, Geld Terug Garantie Gratulerer Håndoverfres DW620/DW621Innholdsfortegnelse CE-SikkerhetserklæringSikkerhetsforskrifter Fjern nøkler Kontroll av pakkens innholdEkstra sikkerhetsregler for freser Bruk av skjøteledning Elektrisk sikkerhetMontering og justering Bruksanvisning Vedlikehold Dagers FORNØYD-KUNDEGARANTI Parabéns Tupia DW620/DW621Conteúdo Dados técnicosInstruções gerais Instruções de segurançaTire as chaves de aperto Descrição fig. a Verificação do conteúdo da embalagemRegras adicionais de segurança para fresas Extensões Segurança eléctricaMontagem e afinação Montagem da guia paralela fig. a & E Modo de empregoAjuste da guia paralela fig. F Para conectar o extractor de poeiras fig. a & EManutenção Limpeza Ferramentas indesejadas e o ambienteOnneksi olkoon Jyrsin DW620/DW621Sisällysluettelo Tekniset tiedotVarjeltava lapsilta TurvallisuusohjeetSäilytä työkalua oikein Ota pistoke pois pistorasiastaKuvaus kuva a Pakkauksen sisältöSähköturvallisuus TurvallisuudeksiAsennus ja säädöt Jatkojohdon käyttöKäyttöohjeet Huolto-ohjeita Vi gratulerar Handöverfräs DW620/DW621Innehållsförteckning Tekniska dataVarning SäkerhetsinstruktionerBeskrivning fig. a Kontroll av förpackningens innehållTillkommande säkerhetsföreskrifter för fräsverktyg Bruk med förlängningssladd Elektrisk säkerhetMontering och inställning Inställning av parallellanslaget fig. F Montering av parallellanslaget fig. a & EMontering av en styrhylsa fig. G Tillkoppling av en dammsugare fig. a & ESkötsel Dagars NÖJD-KUND-GARANTI Som alternativ finns en lista på auktoriseradeİçindekiler TebriklerTeknik veriler Avrupa Birliği şartnameye uygunluk beyanDağyerler ve tezgahlar kazaya neden olabilir Güvenlik talimatlarDaima yere sve dengeli basmaya dikkat edin Tanşekil a AmbalajiçindekilerUzatma kablosu Elektrik güvenliğiMontaj ve ayarlar Montaj ve ayarlardan önce mutlaka aletin fişini çekinKesicinin bileziğe doğru tak takkontrol edin KullantalimatlarElektrikli aletiniz, ek yağlama gerektirmez BakTemizlik DW620 DW621 √À∆Eƒ DW620/DW621√‰ËÁ›Â˜ ·ÛÊ·Ï›·˜ EÏÂÁ¯Ô˜ ÙÔ˘ ÂÚȯÔ̤ÓÔ˘ Ù˘ Û˘Û΢·Û›·˜ ∏ÏÂÎÙÚÈ΋ ·ÛÊ¿ÏÂÈ· ‡ıÌÈÛË ÙÔ˘ ‚¿ıÔ˘˜ ÎÔ‹˜ ÂÈÎ. D √‰ËÁ›Â˜ ¯Ú‹Ûˆ˜ ˘ÓÙ‹ÚËÛË Page Deutschland 11-99
Related manuals
Manual 28 pages 46.33 Kb

DW621 specifications

The DeWalt DW621 is a premium plunge router that showcases the brand's commitment to quality and performance for both professionals and serious woodworking enthusiasts. This router is specifically designed for precision woodworking tasks, making it an essential tool for cabinet makers, furniture creators, and hobbyist woodworkers alike.

One of the standout features of the DW621 is its powerful 2.25 horsepower motor. This robust motor is designed to handle various routing tasks, from trimming to mortising, without compromising speed or stability. With its variable speed control that ranges from 8,000 to 24,000 RPM, users can easily adjust the speed to match the specific material being worked on and the desired finish. This feature enhances the router’s versatility and ensures optimal results for different applications.

The DW621 also incorporates electronic soft-start technology, which allows the motor to gradually ramp up to full speed. This minimizes startup torque and helps prevent the router from "jumping," ensuring a smoother and more controlled operation right from the start. Additionally, the unit is equipped with a precise depth adjustment system. The depth adjustment ring is easy to read and offers micro-fine depth adjustments, enabling users to achieve the exact depth needed for intricate cuts.

Another significant characteristic of the DW621 is its dual, durable precision-machined aluminum bases. The fixed base is designed to be sturdy and provides stability during use, while the plunge base features ergonomic handles for better control and comfort. The plunge mechanism allows for smooth and accurate plunging, which is crucial for creating clean and precise cuts in various applications.

Safety features are also a priority with the DeWalt DW621. The router is designed with an integrated dust collection system that helps maintain a cleaner workspace by capturing dust and debris during operation. This feature not only improves visibility for the user but also contributes to a safer working environment.

In summary, the DeWalt DW621 is more than just a plunge router; it combines powerful performance with precision and user-friendly features. Its robust motor, variable speed control, soft-start technology, and precise depth adjustments make it a top choice for any serious woodworking project. With its blend of durability, functionality, and safety features, the DW621 remains a trusted tool in the woodworking industry, ensuring that users can achieve exceptional results every time.
Top Page Image Contents