Hitachi C 10FCB instruction manual Before Using

Page 11

English

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied wrench, tighten the bolt on the arbor shaft to secure the saw blade. For details, see Fig. 28-a and Fig. 28-b in the section on “SAW BLADE MOUNTING AND DISMOUNTING”.

5. Check the safety cover for proper operation.

Safety cover is designed to protect the operator from coming into contact with the saw blade during operation of the tool.

Always check that the safety cover moves smoothly and covers the saw blade properly.

Safty Cover

Fig. 6

WARNING: Never operate the power tool if the safty cover does not function smoothly.

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position before using the power tool (see Fig. 28-a).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Confirm that the saw blade can be lowered 1-5/8" to 1-21/32" (41 mm to 42 mm) below the table insert. For details, see the section on “Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if it is faulty.

9. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

10. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.

11. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably unstable; otherwise vibrations might occur and cause an accident.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Advertencia AvertissementContents Important Information Meanings of Signal WordsInportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts USE Proper Extension Cord Replacement PartsDouble Insulation for Safer Operation Name of Parts Operation and Maintenance10FCB SpecificationsReleasing the locking pin InstallationApplications Preparation Before OperationBefore Using Confirmation for use of sub fence Before CuttingCutting a groove on the table insert Checking the saw blade lower limit positionSecuring the workpiece Installing the holders Optional accessoryOblique angle Practical Applications Stopper Optional accessory for precision cuttingSwitch operation Cutting Operation Using the vise assembly Standard accessoryCompound cutting procedures Miter cutting proceduresBevel cutting procedures For bevel cut setting Crown molding cutting proceduresFor miter cut setting Cutting easily-deformed materials, such as aluminum sash How to use the dust bagDismounting the saw blade Maintenance and InspectionSAW Blade Mounting and Dismounting Mounting the saw blade -a and -bInspecting the mounting screws Inspecting the safety cover for proper operationCleaning Inspecting the carbon brushes and FigService and Repairs Consignes DE Sécurité Relatives AUX Outils Électriques Informations ImportantesSignification DES Mots D’AVERTISSEMENT Français Consignes de sécurité spéciales pour cet outil électrique Français Double Isolation Pour UN Fonctionnement Plus SUR Pieces DE RechangeUtilisation D’UN Cordon DE Rallonge NOM DES Pièces Utilisation ET EntretienSpécifications Libérer la goupille de verrouillage Préparation Avant L’UTILISATIONAvant L’UTILISATION Vérification du fonctionnement de la garde secondaire Avant LA CoupeCoupe d’une encoche dans la plaque d’insertion Vérification de la position de limite inférieure de la lameFixation de la pièce Installation des servantes Accessoire en optionAngle oblique Fonctionnement de l’interrupteur Butée Accessoire en option pour coupe de précisionApplications Pratiques Coupe Utilisation de l’ensemble d’étau accessoire standardProcédures de coupe mixte Procédure de coupe d’ongletProcédure de coupe de biseau Réglage d’une coupe de biseau Procédures de coupe de corniche complexeRéglage d’une coupe d’onglet Utilisation du sac à copeaux Accessoire standard Retrait de la lame Installation ET Retrait DE LA LameInstallation de la lame -a et -b Entretien ET InspectionVérifier si le carter de sécurité fonctionne correctement Inspection de la lameInspecter les balais carbone et Fig Inspection des vis de montageNettoyage Service APRÈS-VENTE ET RéparationsNormas DE Seguridad Para LAS Herramientas Eléctricas Información ImportanteSignificado DE LAS Palabras Clave Español Español Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Piezas DE ReemplazoUtilización DE UN Cable Prolongador Nomenclatura DE Partes Operación Y MantenimientoEspecificaciones Liberación del pasador de bloqueo AplicacionesPreparativos Previos a LA Operación InstalaciónAntes DE LA Utilización Confirmación sobre el uso de la escuadra de guía secundaria Antes DEL CorteCorte de ranura en un inserto de la mesa Instalación de los soportes Accesorio opcionales Ángulo oblicuoInmovilización de la pieza de trabajo Operación del interruptor Aplicaciones PrácticasTope Accesorio opcionales para corte de precisión Operación de corte Procedimientos de corte compuesto Procedimiento de corte de ingletesProcedimientos de corte en bisel Para el ajuste del corte en bisel Procedimientos de corte con moldura en vérticePara el ajuste de corte de ingletes Tablón de madera Marco corredizo de aluminio Montaje de la hoja de sierra -a y -b Montaje Y Desmontaje DE LA Hoja DE SierraForma de utilizar la bolsa para el polvo Accesorio estándar Mantenimiento E Inspección Limpieza Servicio Y ReparacionesAlmacenamiento LubricaciónPage Page Page Page Hitachi Koki Canada Co
Top Page Image Contents