58HDV
|
|
|
| Plastic Cap |
| Coupling & Clamps |
Single Pressure Switch Detail |
|
|
| Yellow or black |
| |
|
|
|
|
| (Optional) | |
AIR FLOW |
|
|
|
|
|
|
|
|
|
| Vent Drain | EXHAUST | Supplied Tee |
|
|
|
|
|
| Field |
|
|
|
| & Clamps |
|
|
|
|
|
| Level or Sloped |
|
|
|
|
|
| towards Tee |
|
|
|
|
|
|
|
| Tee Trap |
|
|
|
|
|
| White PVC |
|
|
|
|
|
| (loose parts bag) |
Relief Tube |
|
|
|
| Elbow Tube Black Rubber | |
3/ |
|
|
| 1/ ″ (12.7mm) ID & Clamps | ||
Black Rubber | ″ |
|
| |||
|
| 2 |
| |||
(4.8mm) ID | 16 |
|
| (Loose Parts Bag) | ||
|
|
|
|
|
| |
|
|
|
|
| On Some Models | |
|
|
|
|
| ONLY |
|
Flexible Tubing Connector | 3/ | ″ |
|
|
|
|
| 16 |
|
|
| INLET |
|
(4.8mm) OD (Loose Parts Bag) |
|
|
|
| ||
|
|
|
|
| ||
|
|
|
| OFF |
|
|
Relief Tube Extension |
|
| ON |
|
| |
|
|
| Alternate Orientation | |||
Black Rubber 3/ ″ (4.8mm) ID |
|
| ||||
16 |
|
|
|
|
|
|
Cut to Fit (Loose Parts Bag) |
|
|
|
| ||
|
| Dual Pressure Switch | Remove KO before |
|
| |
|
| mounting Trap |
|
| ||
Drain Tube Black, 5/ ″ (15.9mm) ID & Clamps |
|
|
| |||
|
| 8 |
| Drain Tube | Barbed Coupling 1/2″ (12.7mm) | |
Corrugated Cut at straight section |
| |||||
|
|
|
| Black Rubber | OD (Loose Parts Bag) | |
|
|
|
| 1/ ″ (12.7mm) ID | ||
|
|
|
|
|
| |
|
|
|
| 2 |
|
|
|
|
|
| & Clamps |
|
|
|
| Leave room for clamp | Cut Here |
|
| |
Representative drawing only, some models may vary in appearance.
A07712
Fig. 19 - Horizontal Right Side Vent
Horizontal Right-Side Vent (See Fig. 19)
Disconnect drain tee if installed
Disconnect the hoses from the trap assembly, and remove trap and trap mounting bracket from the blower compartment. Using cover plate and gasket provided in the loose parts bag, cover the hole from the burner compartment to the blower compartment and secure with screws.
Remove knockout from the side of the furnace casing where drain tube will exit.
Mount the trap externally to the bottom side of the unit using the two(2) screws provided in the location shown.
Cut the corrugated tube as shown in the illustration above. Connect the corrugated hose from the transition to the trap. Secure connections with clamps.
Connect the black 1/2″ (12.7mm) ID drain tube from the Vent Drain to the trap. If an extension is required, use the 1/2″ (12.7mm) OD barbed coupling and the black 1/2″ (12.7mm) ID drain tube in the loose parts bag. Cut tube to length. Secure connections with clamps.
Connect the 3/16″ (4.8mm) ID relief tube to the middle port on the trap. If an extension is required, use the clear 3/16″ (4.8mm) OD splice connector and the black 3/16″ (4.8mm) ID relief tube in the loose parts bag. Cut tube to length.
Cut an appropriate length of 2″ (50.8mm) PVC pipe, fittings and extension pipe long enough to exit the cabinet and connect the vent drain to either:
SA 2″ (50.8mm) PVC coupling fastened onto the drain tee Install tee trap into bottom section of tee and glue pipe.
Important: The pipe to the tee trap must be level or sloping towards the tee trap
Connect the tee trap and the main drain line exiting the casing as shown in Fig. 19.
NOTE: It is recommended that all PVC piping and fitting connections be fit up and inspected before final cementing. Both the external trap and the external tee trap must be primed before operation. Verify all condensate drain connections are securely clamped. A coupling and clamps (in loose part bag) may be installed as shown for future servicing of the vent system.
26