Trane CAH-SVX01A-EN, Custom Climate Changer Air Handlers manual Apply butyl tape to shipping splits

Page 18

Installation

• Apply 1.25-inch x 0.33-inch

• Move the next unit section as

ribbed butyl tape to the shipping

close as possible from the

split channel and shipping split

previous section. The two

plates (see Figure 11).

sections should be close enough

• Verify the section is level prior to

to reduce the amount of

 

proceeding with the next section

dragging required. This is

particularly important when

of the unit.

mounting on a roof curb to

 

 

 

 

 

 

minimize damage to the sealant

 

 

 

on the roof curb. Alignment of

 

 

 

sections must be completed

 

 

 

before drawing sections

 

 

 

together.

 

 

 

• Remove the bottom bolts from

 

 

 

the shipping split lifting lugs (see

 

 

 

Figure 12).

Figure 11. Apply butyl tape to shipping splits

 

 

 

 

18

Figure 12. Remove bottom bolts from lifting lugs

CAH-SVX01A-EN

Image 18
Contents Custom Climate Changer Air Handlers JulyCAH-SVX01A-EN Unit Description Protecting EnvironmentContents Controls Wiring Sizes ConnectionsOperating Environment Factory-Mounted ControlsUltraviolet UV Germicidal Irradiation Lights optional Job Site Storage Recommendations Receiving ChecklistResolving Shipping Damage Use Canvas OnlyLong-Term Storage Pre-Installation Requirements General StoragePreparing the Unit Site Outdoor Storage ConsiderationsRoof Curb Installation Typical Curb Installation ChecklistLifting and Rigging General Lifting ConsiderationsUnit Assembly Assembly HardwareTCP Model Assembly Instructions Joining Sections Edge-to- EdgeTCP Base Section Assembly Typical TCP base assemblyInstallation TCP Wall Section Assembly Typical TCP Outdoor Roof Section Assembly TypicalIndoor Roof Assembly Complete Installation TCP Indoor Roof Section Assembly TypicalBase to Wall Assembly Complete TCC Model Assembly Instructions Joining sections Edge to EdgeApply butyl tape to shipping splits Add caulk along the seam Join internal shipping split frame TCC wall sections assembly typical Installation TCC indoor roof sections assembly typicalInstallation TCC outdoor roof sections assembly typical Join outdoor roof panels at the seamsTrim roof joint strip Duct Connections Component Installation RequirementsIsolator Adjustment FansTraq Dampers Control DampersMagnahelic Air Filter Gage Installation Air Filters Front Load FiltersOutdoor Unit Weather Hoods Bag or Cartridge FiltersGeneral Recommendations Use a Backup WrenchCoil Piping Connections Prevent Coil DamageInstallation Drain Pan Trapping Water DamageInstallation Steam Coil Piping Coil DamageInstallation Water Coil Piping Typical piping for type 5W one-row water coilInstallation Refrigerant Coil Piping Liquid LinesValve Damage Type F refrigerant coil with packed elbowExamples of Field-Installed Evaporator Piping Single-circuit evaporator coil with one distributorSingle-circuit evaporator coil with two distributors Single-circuit evaporator coil with four distributors Dual-circuit evaporator coil with two distributors Dual-circuit evaporator coil with four distributors Dual-circuit evaporator coil with eight distributors Use Copper Conductors Only WiringHazardous Voltage with CapacitorsJunction box mounting and wiring details External Insulating RequirementsCoil-Related Checks Proper Water Treatment Pre-Startup ChecklistFan-Related Checks Motor-Related ChecksUnit Operation General ChecksCalculate Motor Voltage Imbalance Startup Tension the Fan Belt Tension Belts CorrectlyStartup Determine Fan Speed Sheave AlignmentMultibelt Check Routine Maintenance Permanent Filters Air FiltersThrowaway Filters Front Load FiltersFans Inspecting and Cleaning FansDrain Pans Bearing Set Screw AlignmentFan Bearing Lubrication Fan Motor InspectionType K Cooling Coils CoilsSteam and Water Coils Refrigerant CoilsMoisture Purge Cycle Internal Insulation Replacement of ultraviolet bulbs Ultraviolet UV Germicidal Irradiation LightsTroubleshooting Alignment section on CAH-SVX01A-EN CAH-SVX01A-EN Trane