Craftsman 139.5391 owner manual ALL ONE-PIECE Doors, Adjustment procedures, Figure

Page 26

ALL ONE-PIECE DOORS

1.Assemble the door arm, Figure 4:

•Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap).

•With the door closed, connect the straight door arm section to the door bracket with the

5/16"xl -1/4" clevis pin.

•Secure with a ring fastener.

2.Adjustment procedures, Figure 5:

•On one-piece doors, before connecting the door arm to the trolley, the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 27. Follow adjustment procedures below.

•Open door adjustment: decrease UP travel limit

-Turn the UP limit adjustment screw counter-clockwise 4 turns.

-Press the Door Control push button. The trolley wilt travel to the fully open position.

-Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to

the fully open trolley/door arm positions in the illustration. If the arm does not extend far

enough, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

•Closed door adjustment: decrease DOWN travel limit

-Turn the DOWN limit adjustment screw clockwise 4 complete turns.

Figure 5

Inner Trolley

Outer Trolley

Emergency

Door Arm

Closed

Inner Trolley

Door

 

 

Bracket

 

 

 

Fastener

Nuts

 

 

 

Lock

5/16"-18

 

Washers

 

 

5/16"

 

Clevis Pin

Straight

 

5/16"x1-1/4"

Arm

 

 

Bolts

Cuwed

 

5/16"_18x7/8

Figure 4

DoorArm

 

 

 

-Press the Door Control push button. The trolley will travel to the fully closed position.

-Manually close the door and lift the door arm to

the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to

the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector

hole, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

3.Connect the door arm to the trolley:

•Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be necessary to lift the door slightly to make the connection.

•Secure with a ring fastener.

•Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

NOTE: When setting the up limit on the following page, the door should not have a "backward' slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position.

Release Handle

Outer Trolley

± _.ii-]:

 

Backward Slant

Open Door

(Incorrect)

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Garage Door Opener Abridor DE Puerta DE Cochera Table of Contents Sectional Door One-Piece Door Preparing your garage doorTools needed Planning Sectional Door InstallationSectional Door Installations ONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Carton Inventory Assembly Hardware Hardware InventoryAssembly Step Assemble the Rail & Install the lolleyInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable RexScrewsTrolley InstallationTighten the Chain Installation Step Determine the Header Bracket LocationCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach the Rail to the Header Bracket Position the Opener Sectional Door or ONE-PIECEDOOR with TrackHang the Opener HiddenInstall the Door Control Outside Keylock Accessory ConnectionsInstall the Light Attach the Emergency Release Rope and HandleElectrical Requirements Facing the door from inside the garage Install The Protector SystemImportant Information about Safety Reversing Sensor Installing the Brackets Wall installationTroubleshooting the Safety Sensors Mounting and Wiring the Safety SensorsAligning the Safety Sensors Ure Fasten the Door BracketSectional Doors ONE-PIECE Doors Screws not provided to fasten the bracket to the doorConnect Door Arm to Trolley Sectional Doors onlyALL ONE-PIECE Doors Adjustment procedures, FigureClosed door adjustment decrease Down travel limit Travel cycle after each adjustment Adjustment StepAdjust the UP and Down Travel Limits HOW and When to Adjust the LimitsTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test The Protector System Test the Safety Reversal SystemAdjust TestActivate your opener with any of the following Using Your Garage Door OpenerOperation Lockout position Using Wall.Mounted To Open the Door Manually ControlDisconnect the Trolley TrolleTwice a Year Care of Your OpenerOnce a Month Once a YearMy remotes will not activate the door Having a PROBLEM?My lights will not turn off when door is open My door reverses for no apparent reasonTom Motor unit doesnt operate Symptom LED is not lit on door controlNot glow steady Programming To Add or Reprogram a Hand.held Remote ControlUsing the Learn Button Using the Premium Control Console To Erase All Codes From Motor Unit MemoryUsing the Learn Button Using the Premium Control Console Add, Reprogram Or Change Keyless Entry PINDescription Repair PartsRail Assembly Parts Installation Parts MotorUnitAsmblyPas ExtemsiOn Bracketsi 139.53786 AccessoriesWA R RJ 139i53709DO Gleaan BrakeRevisi6n de los Simbolos y Trminos de Seguridad Preparaci6n de !,,1 puerta de su cochera Herramientas necesariasPlanificaci6n Instalacin CON UNA Puerta SeccionalPlanificaci6n continUa INSTALACI6N CON Puertas DE UNA Sola PiezaInventario de la Caja de Cart6n Inventario de Piezas Rcrascadtrol TORNILLERfA Y Piezas Para LA InstalacinMonte el Riel e instale el Trole Fije el Riel a la Unidad del Motor Instale la Polea LocaIii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iiTEIA Instale la Cadena y CableInstruccion ES IM Portantes Para Apriete la CadenaINSTALACION, Paso Determine d6nde va a instalar La M6nsula del CabezalInstale la Mnsula del Cabezal Coloque el Riel en la Mnsula del Cabezal Coloque el Abridor en Posici6n Retire la espuma de embalajeCuelgue el Abridor Instale la Unidad de Control de la Puerta Conexiones pare la Unidad de Control ExteriorColoque la Cuerda y la Manija de Emergencia Instale la Luce¢!A Requisitos para la Instalaci6n ElctricaEstos sensoresse deben instalaren el interiorde la Instale La Sistema de Protecci6nSi se instalay se alinea oorreotamente, el sensordel Instatacl6n en el p!$o Flgura SiguientesInstatacl6n en la pazd Flgura 2 y La ilustraci6nCOMe Alinear LOS Sensores DE Seguridad INSTALACION, Paso 1 Fije la Mnsula de la PuertaPuertas DE UNA Sola Pieza Conecte el Brazo de la Puerta al Trole FlguraProcedlmlento de ajuste, Flgura Conecte e! braze de la puerta a! troteAjuste el Limite del Recorrido Hacia Arriba y Hacia Abajo St la puerta no se abre per !o menos 1.5 m 5 piesAjuste la Fuerza Pruebe la fuerza de/recorrldo Hacia Arriba abrlrAjuste Pruebe el Sistema de Retroceso de SeguridadPruebe La Sistema de Protecci6n Para reducir el riesgo de lesiones graves o la muerte C6mo Usar su Abridor de Puerta de CocheraMarius C6mo Usar la Unidad de Control de ParedC6mo Abrir la Puerta Manualmente ERTErt¢i AscondicionesSl Tiene Algun Problema Tabla de Diagn6stico Sfntoma E! LED del control de ta puerta no se enclendeSuelte los botones cuandolab lucos C6mo Agrogar o Reprogramar Un Control Remoto ManualCoro Usar LA Consola DE Control Premium Controles Remotos FuncionesEnoendida por 30 segundos Para porter un PiN temporal$61o estan dlsponlbles a travd$ de Reface!ones y Servlclo SearsMY-HOME
Top Page Image Contents