Craftsman 139.5391 Mounting and Wiring the Safety Sensors, Aligning the Safety Sensors

Page 22

MOUNTING AND WIRING THE SAFETY SENSORS

•Slide a 1/4"-20xl/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5).

•Finger tighten the wing nuts.

•Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling.

•Strip 1/4" (6 mm) of insulation from each set of wires. Separate white and white/black wires sufficiently to connect to the terminal screws: white to 2 and white/black to 3 (Figure 6).

ALIGNING THE SAFETY SENSORS

•Plug in the opener. The indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct.

The sending eye orange indicator light will glow regardless of alignment or obstruction. If the green indicator light in the receiving eye is off, dim, or flickering (and the invisible light beam path is not obstructed), alignment is required.

•Loosen the sending eye wing nut and readjust, aiming directly at the receiving eye. Lock in place.

•Loosen the receiving eye wing nut and adjust sensor until it receives the sender's beam. When

the green indicator light glows steadily, tighten the wing nut.

Figure 6

	Bell Wire	Finished
	Bell Wire	Ceiling
		Ceiling

Figure 5

TROUBLESHOOTING THE SAFETY SENSORS

1.If the sending eye indicator light does not glow steadily after installation, check for:

•Electric power to the opener.

•A short in the white or white/black wires. These can occur at staples, or at opener connections.

•Incorrect wiring between sensors and opener.

•A broken wire.

2.If the sending eye indicator light glows steadily but the receiving eye indicator light doesn't:

•Check alignment.

•Check for an open wire to the receiving eye.

3.If the receiving eye indicator light is dim, realign either sensor.

NOTE: When the invisible beam path is obstructed or misaligned while the door is closing, the door will reverse. If the door is already open, it will not close. The opener lights will blink 10 times. See page 20.

Connect Wire to

Terminal Screws

	Bell Wire	/
	Bell Wire
	DoorControl	Sensor
	DoorControl	Connections
	Connections	Connections
	Connections
	(do_edline)	_
		OPENER TERMINAL SCREWS

Sensor_

	Invisible Light	Beam
\ Sensor	Protec_onArea

22

Image 22

Contents Garage Door Opener Abridor DE Puerta DE Cochera Table of Contents Tools needed Preparing your garage doorSectional Door One-Piece Door Sectional Door Installations Sectional Door InstallationPlanning ONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track Carton Inventory Assembly Hardware Hardware InventoryAssembly Step Assemble the Rail & Install the lolleyInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable RexScrewsTighten the Chain InstallationTrolley Installation Step Determine the Header Bracket LocationWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Attach the Rail to the Header Bracket Position the Opener Sectional Door or ONE-PIECEDOOR with TrackHang the Opener HiddenInstall the Door Control Outside Keylock Accessory ConnectionsInstall the Light Attach the Emergency Release Rope and HandleElectrical Requirements Important Information about Safety Reversing Sensor Install The Protector SystemFacing the door from inside the garage Installing the Brackets Wall installationAligning the Safety Sensors Mounting and Wiring the Safety SensorsTroubleshooting the Safety Sensors Sectional Doors Fasten the Door BracketUre ONE-PIECE Doors Screws not provided to fasten the bracket to the doorConnect Door Arm to Trolley Sectional Doors onlyClosed door adjustment decrease Down travel limit Adjustment procedures, FigureALL ONE-PIECE Doors Travel cycle after each adjustment Adjustment StepAdjust the UP and Down Travel Limits HOW and When to Adjust the LimitsHOW and When to Adjust the Forces Adjust the ForceTest the Down close force Test The Protector System Test the Safety Reversal SystemAdjust TestOperation Using Your Garage Door OpenerActivate your opener with any of the following Lockout position Using Wall.Mounted To Open the Door Manually ControlDisconnect the Trolley TrolleTwice a Year Care of Your OpenerOnce a Month Once a YearMy remotes will not activate the door Having a PROBLEM?My lights will not turn off when door is open My door reverses for no apparent reasonNot glow steady Symptom LED is not lit on door controlTom Motor unit doesnt operate Programming To Add or Reprogram a Hand.held Remote ControlUsing the Learn Button Using the Premium Control Console To Erase All Codes From Motor Unit MemoryUsing the Learn Button Using the Premium Control Console Add, Reprogram Or Change Keyless Entry PINRail Assembly Parts Installation Parts Repair PartsDescription MotorUnitAsmblyPas ExtemsiOn Bracketsi 139.53786 AccessoriesWA R RJ 139i53709DO Gleaan BrakeRevisi6n de los Simbolos y Trminos de Seguridad Preparaci6n de !,,1 puerta de su cochera Herramientas necesariasPlanificaci6n Instalacin CON UNA Puerta SeccionalPlanificaci6n continUa INSTALACI6N CON Puertas DE UNA Sola PiezaInventario de la Caja de Cart6n Inventario de Piezas Rcrascadtrol TORNILLERfA Y Piezas Para LA InstalacinMonte el Riel e instale el Trole Fije el Riel a la Unidad del Motor Instale la Polea LocaIii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iiTEIA Instale la Cadena y CableInstruccion ES IM Portantes Para Apriete la CadenaINSTALACION, Paso Determine d6nde va a instalar La M6nsula del CabezalInstale la Mnsula del Cabezal Coloque el Riel en la Mnsula del Cabezal Coloque el Abridor en Posici6n Retire la espuma de embalajeCuelgue el Abridor Instale la Unidad de Control de la Puerta Conexiones pare la Unidad de Control ExteriorColoque la Cuerda y la Manija de Emergencia Instale la Luce¢!A Requisitos para la Instalaci6n ElctricaSi se instalay se alinea oorreotamente, el sensordel Instale La Sistema de Protecci6nEstos sensoresse deben instalaren el interiorde la Instatacl6n en el p!$o Flgura SiguientesInstatacl6n en la pazd Flgura 2 y La ilustraci6nCOMe Alinear LOS Sensores DE Seguridad INSTALACION, Paso 1 Fije la Mnsula de la PuertaPuertas DE UNA Sola Pieza Conecte el Brazo de la Puerta al Trole FlguraProcedlmlento de ajuste, Flgura Conecte e! braze de la puerta a! troteAjuste el Limite del Recorrido Hacia Arriba y Hacia Abajo St la puerta no se abre per !o menos 1.5 m 5 piesAjuste la Fuerza Pruebe la fuerza de/recorrldo Hacia Arriba abrlrPruebe La Sistema de Protecci6n Pruebe el Sistema de Retroceso de SeguridadAjuste Para reducir el riesgo de lesiones graves o la muerte C6mo Usar su Abridor de Puerta de CocheraC6mo Abrir la Puerta Manualmente C6mo Usar la Unidad de Control de ParedMarius ERTErt¢i AscondicionesSl Tiene Algun Problema Tabla de Diagn6stico Sfntoma E! LED del control de ta puerta no se enclendeSuelte los botones cuandolab lucos C6mo Agrogar o Reprogramar Un Control Remoto ManualCoro Usar LA Consola DE Control Premium Controles Remotos FuncionesEnoendida por 30 segundos Para porter un PiN temporal$61o estan dlsponlbles a travd$ de Reface!ones y Servlclo SearsMY-HOME