Craftsman 139.5391 owner manual Having a PROBLEM?, My remotes will not activate the door

Page 33

HAVING A PROBLEM?

1.My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.

•Verify the safety sensors are properly installed aligned and free of any obstructions. Refer to Installation Step 10: Install The Protector System _.

•Check diagnostic LED for flashes on the motor unit then refer to the Diagnostic Chart on the following page.

2.My remotes will not activate the door:

•Verify your Premium door control is not blinking. If it is blinking, deactivate the Lock Mode following the instructions for Using the Premium Control Console.

•Reprogram remotes following the programming instructions. Refer to Programming.

•If remote will still not activate your door. check diagnostic LED for flashes on motor unit then refer to Diagnostic Chart on the following page.

3.My door reverses for no apparent reason:

Repeat safety reverse test after adjustments to force or travel limits. The need for occasional

adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

•Manually check door for balance or any binding problems.

•Refer to Adjustment Step 2, Adjust the Force.

4.My door reverses for no apparent reason after fully closing and touching the floor: Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

•Refer to Adjustment Step 1, Adjust the UP and DOWN Travel Limits. Decrease down travel by turning down limit adjustment screw clockwise.

5.My lights will not turn off when door is open:

•The garage door opener is equipped with a security light feature. This feature activates the light on when the safety sensor beam has been obstructed Refer to Operation section; Using the Wall Mounted Door Control Light Feature

SafetySensor

Sending

Eye Safety Sensor

Receiving Eye

Safety Sensor

(Amber

Indicator Light)

(Green Indicator

Light)

 

 

/

 

6.My motor unit hums briefly:

•First verify that the trolley is against the stop bolt.

•Release the door from the opener by pulling the Emergency Release Rope.

•Manually bring the door to a closed position.

,Loosen the chain by adjusting the outer nut 4 to 5 turns. This relieves the tension.

•Run the motor unit from the remote control or door control. The trolley should travel towards the door and stop. If the trolley re-engages with the door, pull the Emergency Release Rope to disengage.

,Decrease the UP travel by turning the UP Travel adjustment screw 2 fu!l turns away from

the arrow.

•Re-tighten the outer nut so the chain is a 1/4" (6 mm) above the base of the rail. (When the door is reconnected and closed, the chain will sag. This is normal,)

•If the trolley does not move away from the bolt, repeat the steps above.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Garage Door Opener Abridor DE Puerta DE Cochera Table of Contents Preparing your garage door Tools neededSectional Door One-Piece Door Sectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track Carton Inventory Hardware Inventory Assembly HardwareAssemble the Rail & Install the lolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyRexScrews Install the Chain/CableInstallation Tighten the ChainTrolley Determine the Header Bracket Location Installation StepInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Sectional Door or ONE-PIECEDOOR with Track Position the OpenerHidden Hang the OpenerOutside Keylock Accessory Connections Install the Door ControlAttach the Emergency Release Rope and Handle Install the LightElectrical Requirements Install The Protector System Important Information about Safety Reversing SensorFacing the door from inside the garage Wall installation Installing the BracketsMounting and Wiring the Safety Sensors Aligning the Safety SensorsTroubleshooting the Safety Sensors Fasten the Door Bracket Sectional DoorsUre Screws not provided to fasten the bracket to the door ONE-PIECE DoorsSectional Doors only Connect Door Arm to TrolleyAdjustment procedures, Figure Closed door adjustment decrease Down travel limitALL ONE-PIECE Doors Adjust the UP and Down Travel Limits Adjustment StepTravel cycle after each adjustment HOW and When to Adjust the LimitsAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Adjust Test the Safety Reversal SystemTest The Protector System TestUsing Your Garage Door Opener OperationActivate your opener with any of the following Disconnect the Trolley Using Wall.Mounted To Open the Door Manually ControlLockout position TrolleOnce a Month Care of Your OpenerTwice a Year Once a YearMy lights will not turn off when door is open Having a PROBLEM?My remotes will not activate the door My door reverses for no apparent reasonSymptom LED is not lit on door control Not glow steadyTom Motor unit doesnt operate Using the Learn Button Using the Premium Control Console To Add or Reprogram a Hand.held Remote ControlProgramming To Erase All Codes From Motor Unit MemoryAdd, Reprogram Or Change Keyless Entry PIN Using the Learn Button Using the Premium Control ConsoleRepair Parts Rail Assembly Parts Installation PartsDescription MotorUnitAsmblyPas WA R RJ AccessoriesExtemsiOn Bracketsi 139.53786 139i53709DO Gleaan BrakeRevisi6n de los Simbolos y Trminos de Seguridad Herramientas necesarias Preparaci6n de !,,1 puerta de su cocheraInstalacin CON UNA Puerta Seccional Planificaci6nINSTALACI6N CON Puertas DE UNA Sola Pieza Planificaci6n continUaInventario de la Caja de Cart6n Rcrascadtrol TORNILLERfA Y Piezas Para LA Instalacin Inventario de PiezasMonte el Riel e instale el Trole Instale la Polea Loca Fije el Riel a la Unidad del MotorInstale la Cadena y Cable Iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iii!iiTEIAApriete la Cadena Instruccion ES IM Portantes ParaDetermine d6nde va a instalar La M6nsula del Cabezal INSTALACION, PasoInstale la Mnsula del Cabezal Coloque el Riel en la Mnsula del Cabezal Retire la espuma de embalaje Coloque el Abridor en Posici6nCuelgue el Abridor Conexiones pare la Unidad de Control Exterior Instale la Unidad de Control de la PuertaInstale la Luce Coloque la Cuerda y la Manija de EmergenciaRequisitos para la Instalaci6n Elctrica ¢!AInstale La Sistema de Protecci6n Si se instalay se alinea oorreotamente, el sensordelEstos sensoresse deben instalaren el interiorde la Instatacl6n en la pazd Flgura 2 y SiguientesInstatacl6n en el p!$o Flgura La ilustraci6nCOMe Alinear LOS Sensores DE Seguridad Fije la Mnsula de la Puerta INSTALACION, Paso 1Puertas DE UNA Sola Pieza Flgura Conecte el Brazo de la Puerta al TroleConecte e! braze de la puerta a! trote Procedlmlento de ajuste, FlguraSt la puerta no se abre per !o menos 1.5 m 5 pies Ajuste el Limite del Recorrido Hacia Arriba y Hacia AbajoPruebe la fuerza de/recorrldo Hacia Arriba abrlr Ajuste la FuerzaPruebe el Sistema de Retroceso de Seguridad Pruebe La Sistema de Protecci6nAjuste C6mo Usar su Abridor de Puerta de Cochera Para reducir el riesgo de lesiones graves o la muerteC6mo Usar la Unidad de Control de Pared C6mo Abrir la Puerta ManualmenteMarius Ascondiciones ERTErt¢iSl Tiene Algun Problema Sfntoma E! LED del control de ta puerta no se enclende Tabla de Diagn6sticoCoro Usar LA Consola DE Control Premium C6mo Agrogar o Reprogramar Un Control Remoto ManualSuelte los botones cuandolab lucos Controles Remotos FuncionesPara porter un PiN temporal Enoendida por 30 segundosReface!ones y Servlclo Sears $61o estan dlsponlbles a travd$ deMY-HOME
Top Page Image Contents