During the first minute of a cycle, To add items

Kenmore 665.1648 During the first minute of a cycle, After the first minute of a cycle, Air Dry

During the first minute of a cycle

1.Open the door.

2.Press a new cycle and/or options.

3.Check the detergent dispensers. They must be filled properly for the new cycle.

4.Close the door. The dishwasher resumes the new cycle and/or option after a 5-second pause.

After the first minute of a cycle

1.Carefuly open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door to access the control panel.

2.Press CANCEL. The Cancel light glows.

3.Close the door. Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after 2 minutes.

NOTE: If your dishwasher does not need draining, the light turns off.

4.Open the door. Select a new cycle and/or options.

5.Check the detergent dispensers. They must be filled properly for the new cycle.

6.Press START and firmly close the door (on top control models). Or, firmly close the door and press START (on split control models).

You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is stil closed, you can add items.

To add items

1.Carefuly open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door.

2.Open the door. If the detergent dispenser cover is stil closed, add the item.

3.Close the door firmly until it latches. The dishwasher resumes the cycle after about a 5-second pause.

You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off, or select a different option if desired.

You can change an option anytime before the selected option begins. For example, you can press an unheated drying option any time before drying begins.

Press START to use the same cycle and option(s) as the previous wash cycle.

NOTE: If the last cycle you completed was a rinse cycle, when you press Start, the dishwasher runs the last full wash cycle and options.

Hi Temp Wash

Select this option to increase the water temperature during the wash portions of the cycle. Hi Temp Wash raises the water temperature to 145°F (63°C), in the main wash. Heating the water helps improve washing results. Hi Temp Wash is useful when loads contain baked-on food.

This option adds heat, wash time and may add water to the cycle.

NOTE: Hi Temp Wash is an option with the Smart Wash, Anti Bacterial, and Normal Wash cycles.

Sani Rinse

Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). Sani Rinse adds heat and time to the cycle. This high temperature rinse sanitizes your dishes and glassware in accordance with NSF/ANSl Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments.

NOTE: The Anti Bacterial cycle automatically uses this option. Sani Rinse is an option with SmartWash and Normal Wash. Only these sanitization cycles have been designed to meet the NSF/ ANSI requirements.

Air Dry

Select this option to dry without heat. Air drying is useful when loads contain plastic dinnerware that may be sensitive to high temperatures.

The dishes take longer to dry and some spotting can occur. For best drying, use a liquid rinse aid. Some items (such as plastics) may need towel drying.

NOTE: Air Dry is an option with all cycles, except Quick Rinse.

Lock On

Use the Lock On to prevent unintended use of the dishwasher. You can also use the lock feature to prevent unintended cycle or option changes during a cycle.

When LOCK ON is lit, all buttons are disabled.

NOTE: The dishwasher door can be opened while the controls are locked.

To turn on the Lock

Press and hold AIR DRY for 4 seconds. LOCK ON glows.

If you press any pad while your dishwasher is locked, the light flashes 3 times.

To turn off the Lock

Press and hold AIR DRY for 4 seconds. The light turns off.

Delay Hours/4 Hour Delay

Select this option to run your dishwasher at a later time or during off-peak hours. You can add items to the load anytime during the delay. After adding items, firmly close the door until it latches.

The delay will not continue if the door is not latched.

To delay the start

1.Press the delay button to choose the number of hours delayed.

2.Select a wash cycle and options.

3.Press START.

The dishwasher starts the cycle in the selected number of hours.

NOTES:

•TOcancel the delay and cycle, press CANCEL.

•To cancel the delay and start the cycle, press START.