Husqvarna 330X, 320 manual Installation of the charging station, Best charging station location

Page 18

INSTALLATION

4.Check that all parts for the installation are included. The numbers in brackets refer to the component illustration. See 2.1 What is what? on page 10.

• Operator’s Manual (28) • Robotic lawnmower

• Charging station (10)

• Loop wire for boundary loop and guide wire (21)

• Transformer (20)

• Low voltage cable (22) • Pegs (23)

• Connectors for the loop wire (24)

• Screws for the charging station (25) • Measurement gauge (26)

• Couplers for the loop wire (27) During installation you will also need:

• Hammer/plastic mallet (to simplify putting the pegs in the ground).

• Combination pliers for cutting the boundary wire and pressing the connectors and couplers together.

• Edge cutter/straight spade if the boundary wire must be buried.

3018-057

3.2 Installation of the charging station

Best charging station location

Take the following aspects into consideration when identifying the best location for the charging station:

• Allow for at least 3 metres of free space in front of the charging station

• It must be close to a wall socket. The supplied low voltage cable is 10 metres long

• A level surface to place the charging station on

• Protection from water spray for instance from irrigation

• Protection from direct sunlight

• Possible requirement to keep the charging station out of sight for outsiders

English - 16

Image 18

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Guarantee terms Introduction and safety TroubleshootingTechnical Data Garden examples MaintenanceMEMO Introduction and safety IntroductionSymbols on the product Symbols in the Operator’s Manual Text Important Information TextSafety instructions UseMoving Maintenance Presentation What is what? Numbers in the illustration representPackage content FunctionCapacity Mowing technique Working methodMovement pattern Finding the charging stationSearch method 1 Irregular Search method 2 Follow guide wire Search method 3 Follow boundary wireInstallation See 7 Garden examples on page 65 for installation examplesPreparations Installation of the charging station Best charging station location3012-559 Connecting the transformer Installing and connecting the charging station Do not tread or walk on the charging station’s plateCharging the battery Installation of the boundary wire Plan where to lay the boundary wireWorking area boundaries Boundaries within the working area Secondary areasPassages when mowing SlopesLaying the boundary wire Laying the boundary wire in towards the charging Station Splicing the boundary wireConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation First start-up and calibration Test docking with the charging stationUse Memo on page 2 to make a note of the PIN code Charging a flat battery UseUsing the timer StartingSwitching off Adjusting the cutting heightStopping Control panel Operation selection Start Main areaSecondary area Operation selection Parking Main switch Charging station’s Park buttonBrowse between menus Menu functionsMain menu Number seriesTimer Menu structureTimer CopyCurrent day ResetOverview All weekCutting height To increase the cutting heightTo lower the cutting height Function Low Medium High AlarmSecurity Time lockNew loop signal CustomChange PIN code Fault messages MessagesAdvanced Weather timer Weather timerReset messages Info messagesInstallation Cutting timeExample Guide Guide Guide 1 delayGuide Guide 2 delay Boundary loopSetting Range Charging station rangeOverview Test Lawn coverage AreaArea 1-5 How? Area X How far?Area X How often? GPS This section does not apply to AutomowerReset All areas ResetReset Current area Lawn coverage How far?Corridor width Corridor width BoundaryExit angles Sectors Corridor width GuideExit angles Reversing distanceDrive past wire Installation shapeAutomatic passage handling Settings Save settings to a ProfileProfiles Use a Profil Check New loop signal, See 6.5 Security on page 45Change the name of a profile One Automower for several gardensSpiral cutting Spiral cuttingTime & Date CountryCutting height calibration Calibration of guide wire Reset all user settingsSelect Reset all user settings in the menu and press OK Accessories HeadlightMower house Installation proposals and settings Garden examplesFind charging Installation proposals and settingsLawn coverage StationGuide 1 Proportion 60% As the GPS assisted navigationGuide 1 Proportion 40% 3012-978 3018-095 Secondary area mode on Maintenance Winter storage Robotic lawnmowerCharging station After winter storage Winter serviceCleaning Chassis and blade discChassis Transport and movingEvent of a thunderstorm WheelsBattery BladesTroubleshooting Fault messagesTroubleshooting Troubleshooting Info messages Indicator lamp in the charging station Light Cause ActionSymptoms Not rotate Lawnmower runs, butBlade disc does Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Technical Data DataGuarantee terms Environmental information EC Declaration of Conformity EN 61000-6-3 emission EN 61000-6-1 immunityOriginal Instructions