Husqvarna 320, 330X manual Operation selection Start, Main area, Secondary area

Page 39

CONTROL PANEL

The keypad consists of six groups of buttons:

•The START button is used to activate the robotic lawnmower. This is normally the last button to be pressed before closing the display hatch.

• The Back and OK buttons are used to navigate in the menu. The OK button is also used to confirm settings in the menu.

• The arrow keys are used to navigate in the menu but also to make selections in certain setting options.

• The MENU button is used to go to the main menu.

•The PARK button is used to send the robotic lawnmower to the charging station.

•Numbers are used to enter settings, for example, PIN code, time or exit direction. They can also be used to enter a number series for shortcuts to the various menus. See 6.1 Main menu on page 40.

5.1 Operation selection Start

When the START button has been pressed the following operation selections can be selected.

Main area

The standard, automatic operating mode where the robotic lawnmower mows and charges continually.

Secondary area

The Secondary area operating mode is used when mowing secondary areas where the robotic lawnmower cannot travel to the charging station automatically. For information about secondary areas, see 3.4 Installation of the boundary wire on page 21.

Selecting Secondary area offers three options:

• Mowing until empty battery

This option is suitable for a large secondary area requiring more than 90 minutes to mow.

• Mowing 90 min

This option is suitable to prevent unnecessary mowing and trampled grass in a small/medium sized secondary area.

• Mowing 30 min

This option is suitable to prevent unnecessary mowing and trampled grass in a small secondary area.

If the robotic lawnmower charges in the Secondary area mode, it will fully charge, drive out about 50 cm and then stop. This indicates that it is charged and ready to start mowing.

If the main working area has to be cut after charging, it is appropriate to switch the operation selection to Main area before placing the robotic lawnmower in the charging station.

3012-1094

3012-1222

English - 37

Image 39

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Garden examples Maintenance Introduction and safety TroubleshootingTechnical Data Guarantee termsMEMO Introduction Introduction and safetySymbols on the product Text Important Information Text Symbols in the Operator’s ManualUse Safety instructionsMoving Maintenance Presentation Numbers in the illustration represent What is what?Package content FunctionCapacity Working method Mowing techniqueMovement pattern Finding the charging stationSearch method 1 Irregular Search method 3 Follow boundary wire Search method 2 Follow guide wireInstallation See 7 Garden examples on page 65 for installation examplesPreparations Best charging station location Installation of the charging station3012-559 Connecting the transformer Do not tread or walk on the charging station’s plate Installing and connecting the charging stationCharging the battery Plan where to lay the boundary wire Installation of the boundary wireWorking area boundaries Secondary areas Boundaries within the working areaSlopes Passages when mowingLaying the boundary wire Splicing the boundary wire Laying the boundary wire in towards the charging StationConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation First start-up and calibration Test docking with the charging stationUse Memo on page 2 to make a note of the PIN code Use Charging a flat batteryStarting Using the timerSwitching off Adjusting the cutting heightStopping Control panel Operation selection Start Main areaSecondary area Operation selection Parking Charging station’s Park button Main switchNumber series Menu functionsMain menu Browse between menusMenu structure TimerCopy TimerAll week ResetOverview Current dayCutting height To increase the cutting heightTo lower the cutting height Time lock AlarmSecurity Function Low Medium HighNew loop signal CustomChange PIN code Fault messages MessagesAdvanced Info messages Weather timerReset messages Weather timerInstallation Cutting timeExample Boundary loop Guide Guide 1 delayGuide Guide 2 delay GuideSetting Range Charging station rangeOverview Test Area Lawn coverageArea 1-5 How? Area X How far?Area X How often? This section does not apply to Automower GPSLawn coverage How far? ResetReset Current area Reset All areasCorridor width Boundary Corridor widthReversing distance Corridor width GuideExit angles Exit angles SectorsDrive past wire Installation shapeAutomatic passage handling Settings Save settings to a ProfileProfiles One Automower for several gardens Check New loop signal, See 6.5 Security on page 45Change the name of a profile Use a ProfilSpiral cutting Spiral cuttingTime & Date CountryCutting height calibration Calibration of guide wire Reset all user settingsSelect Reset all user settings in the menu and press OK Accessories HeadlightMower house Garden examples Installation proposals and settingsStation Installation proposals and settingsLawn coverage Find chargingGuide 1 Proportion 60% As the GPS assisted navigationGuide 1 Proportion 40% 3012-978 3018-095 Secondary area mode on Maintenance Winter storage Robotic lawnmowerCharging station Chassis and blade disc Winter serviceCleaning After winter storageWheels Transport and movingEvent of a thunderstorm ChassisBlades BatteryFault messages TroubleshootingTroubleshooting Troubleshooting Info messages Light Cause Action Indicator lamp in the charging stationSymptoms Lawnmower mows Lawnmower runs, butBlade disc does Not rotateFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Data Technical DataGuarantee terms Environmental information EN 61000-6-3 emission EN 61000-6-1 immunity EC Declaration of ConformityOriginal Instructions