Husqvarna 330X, 320 manual Symbols on the product

Page 6

INTRODUCTION AND SAFETY

1.2 Symbols on the product

These symbols can be found on the robotic lawnmower.

Study them carefully.

Please read the Operator’s Manual carefully and make sure you understand the instructions before using the robotic lawnmower. The warnings and safety instructions in this Operator’s Manual must be carefully followed if the robotic lawnmower is to be used safely and efficiently.

• The robotic lawnmower can only start when the main switch is set to 1 and the correct PIN code has been entered. Turn the main switch to 0 before carrying out any inspections and/or maintenance.

Remain at a safe distance from the robotic

lawnmower when it is running. Keep your hands and feet away from the rotating blades. Never put your hands or feet close to or under the body when the robotic lawnmower is running.

• Do not ride on the robotic lawnmower.

This product conforms to the applicable EC Directives.

• Noise emission to surroundings. The product’s emissions are set out in chapter 10, Technical data and on the rating plate.

It is not permitted to dispose of this product as normal household waste when it has reached the end of

its useful life. Ensure that the product is recycled in accordance with local legal requirements.

Never use a high-pressure washer or even running water to clean the robotic lawnmower.

1001-002, 1001-003

3012-663, 3012-1085

3018-066

3012-665

6001-024

3012-1059

3012-689

3018-062

English - 4

Image 6
Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Guarantee terms Introduction and safety TroubleshootingTechnical Data Garden examples MaintenanceMEMO Introduction and safety IntroductionSymbols on the product Symbols in the Operator’s Manual Text Important Information TextSafety instructions UseMoving Maintenance Presentation What is what? Numbers in the illustration representPackage content FunctionCapacity Mowing technique Working methodMovement pattern Finding the charging stationSearch method 1 Irregular Search method 2 Follow guide wire Search method 3 Follow boundary wireInstallation See 7 Garden examples on page 65 for installation examplesPreparations Installation of the charging station Best charging station location3012-559 Connecting the transformer Installing and connecting the charging station Do not tread or walk on the charging station’s plateCharging the battery Installation of the boundary wire Plan where to lay the boundary wireWorking area boundaries Boundaries within the working area Secondary areasPassages when mowing SlopesLaying the boundary wire Laying the boundary wire in towards the charging Station Splicing the boundary wireConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation First start-up and calibration Test docking with the charging stationUse Memo on page 2 to make a note of the PIN code Charging a flat battery UseUsing the timer StartingSwitching off Adjusting the cutting heightStopping Control panel Operation selection Start Main areaSecondary area Operation selection Parking Main switch Charging station’s Park buttonBrowse between menus Menu functionsMain menu Number seriesTimer Menu structureTimer CopyCurrent day ResetOverview All weekCutting height To increase the cutting heightTo lower the cutting height Function Low Medium High AlarmSecurity Time lockNew loop signal CustomChange PIN code Fault messages MessagesAdvanced Weather timer Weather timerReset messages Info messagesInstallation Cutting timeExample Guide Guide Guide 1 delayGuide Guide 2 delay Boundary loopSetting Range Charging station rangeOverview Test Lawn coverage AreaArea 1-5 How? Area X How far?Area X How often? GPS This section does not apply to AutomowerReset All areas ResetReset Current area Lawn coverage How far?Corridor width Corridor width BoundaryExit angles Sectors Corridor width GuideExit angles Reversing distanceDrive past wire Installation shapeAutomatic passage handling Settings Save settings to a ProfileProfiles Use a Profil Check New loop signal, See 6.5 Security on page 45Change the name of a profile One Automower for several gardensSpiral cutting Spiral cuttingTime & Date CountryCutting height calibration Calibration of guide wire Reset all user settingsSelect Reset all user settings in the menu and press OK Accessories HeadlightMower house Installation proposals and settings Garden examplesFind charging Installation proposals and settingsLawn coverage StationGuide 1 Proportion 60% As the GPS assisted navigationGuide 1 Proportion 40% 3012-978 3018-095 Secondary area mode on Maintenance Winter storage Robotic lawnmowerCharging station After winter storage Winter serviceCleaning Chassis and blade discChassis Transport and movingEvent of a thunderstorm WheelsBattery BladesTroubleshooting Fault messagesTroubleshooting Troubleshooting Info messages Indicator lamp in the charging station Light Cause ActionSymptoms Not rotate Lawnmower runs, butBlade disc does Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Technical Data DataGuarantee terms Environmental information EC Declaration of Conformity EN 61000-6-3 emission EN 61000-6-1 immunityOriginal Instructions