Husqvarna 320, 330X manual Installation, Preparations

Page 17

INSTALLATION

3 Installation

This chapter describes how to install the robotic lawnmower. Before starting the installation read the previous chapter 2. Presentation.

Read also through this entire chapter before beginning the installation. How the installation is done also affects how well the robotic lawnmower works. It is therefore important to plan the installation carefully.

Planning is simplified if you make a sketch of the working area, including all obstacles. This makes it easier to see the ideal positions for the charging station, the boundary wire and the guide wire. Draw on the sketch where the boundary and guide wires should be routed.

See 7 Garden examples on page 65 for installation examples.

Visit also www.automower.com for further descriptions and tips regarding installation.

Carry out the installation as outlined in the following steps:

3.1Preparations

3.2Installation of the charging station

3.3Charging the battery

3.4Installation of the boundary wire

3.5Connecting the boundary wire

3.6Installation of the guide wire

3.7Checking the installation

3.8First start-up and calibration

3.9Test docking with the charging station

The charging station, boundary loop and guide wire must be connected to be able to carry out a complete start-up.

3.1Preparations

1.If the lawn in the working area is longer than 10 cm mow it using a standard lawnmower. Then collect the grass.

2. Fill in holes and hollows to stop rainwater forming pools of water. The product may be damaged if it is operated in pools of water. See 11 Guarantee terms on page 87.

3. Read carefully through all the steps before the
installation.	3012-1101

English - 15

Image 17

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Technical Data Introduction and safety TroubleshootingGuarantee terms Garden examples MaintenanceMEMO Introduction Introduction and safetySymbols on the product Text Important Information Text Symbols in the Operator’s ManualUse Safety instructionsMoving Maintenance Presentation Numbers in the illustration represent What is what?Capacity Package contentFunction Working method Mowing techniqueSearch method 1 Irregular Movement patternFinding the charging station Search method 3 Follow boundary wire Search method 2 Follow guide wirePreparations InstallationSee 7 Garden examples on page 65 for installation examples Best charging station location Installation of the charging station3012-559 Connecting the transformer Do not tread or walk on the charging station’s plate Installing and connecting the charging stationCharging the battery Plan where to lay the boundary wire Installation of the boundary wireWorking area boundaries Secondary areas Boundaries within the working areaSlopes Passages when mowingLaying the boundary wire Splicing the boundary wire Laying the boundary wire in towards the charging StationConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation Use Memo on page 2 to make a note of the PIN code First start-up and calibrationTest docking with the charging station Use Charging a flat batteryStarting Using the timerStopping Switching offAdjusting the cutting height Control panel Secondary area Operation selection StartMain area Operation selection Parking Charging station’s Park button Main switchMain menu Menu functionsBrowse between menus Number seriesMenu structure TimerCopy TimerOverview ResetCurrent day All weekTo lower the cutting height Cutting heightTo increase the cutting height Security AlarmFunction Low Medium High Time lockChange PIN code New loop signalCustom Advanced Fault messagesMessages Reset messages Weather timerWeather timer Info messagesExample InstallationCutting time Guide Guide 2 delay Guide Guide 1 delayGuide Boundary loopOverview Test Setting RangeCharging station range Area Lawn coverageArea X How often? Area 1-5 How?Area X How far? This section does not apply to Automower GPSReset Current area ResetReset All areas Lawn coverage How far?Corridor width Boundary Corridor widthExit angles Corridor width GuideExit angles Sectors Reversing distanceAutomatic passage handling Drive past wireInstallation shape Profiles SettingsSave settings to a Profile Change the name of a profile Check New loop signal, See 6.5 Security on page 45Use a Profil One Automower for several gardensSpiral cutting Spiral cuttingCutting height calibration Time & DateCountry Select Reset all user settings in the menu and press OK Calibration of guide wireReset all user settings Mower house AccessoriesHeadlight Garden examples Installation proposals and settingsLawn coverage Installation proposals and settingsFind charging StationGuide 1 Proportion 40% Guide 1 Proportion 60%As the GPS assisted navigation 3012-978 3018-095 Secondary area mode on Maintenance Charging station Winter storageRobotic lawnmower Cleaning Winter serviceAfter winter storage Chassis and blade discEvent of a thunderstorm Transport and movingChassis WheelsBlades BatteryFault messages TroubleshootingTroubleshooting Troubleshooting Info messages Light Cause Action Indicator lamp in the charging stationSymptoms Blade disc does Lawnmower runs, butNot rotate Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Data Technical DataGuarantee terms Environmental information EN 61000-6-3 emission EN 61000-6-1 immunity EC Declaration of ConformityOriginal Instructions