Husqvarna 320, 330X manual Corridor width Guide, Exit angles Sectors, Reversing distance

Page 59

MENU FUNCTIONS

Corridor width > Guide

In the case of the guide wires, specify the widest distance from each guide wire the robotic lawnmower can run. The distance is specified as a figure between 0 and 9. The distance the robotic lawnmower maintains from the guide wire varies depending on the layout of the working area. Use the Test function in Installation > Lawn coverage > Overview to test which value is suitable for the working area in question.

If value 0 is specified, the robotic lawnmower will straddle the guide wire meaning it runs right over the middle of the guide wire.

Use the arrow keys to specify the required value. The factory setting is 9.

Exit angles

Normally the robotic lawnmower leaves the charging station in a direction within the 90°-270° exit sector. By changing the exit angles, it makes it easier for the robotic lawnmower to reach the largest working area if the charging station is placed in a passage.

Exit angles > Sectors

The robotic lawnmower can be set for one or two exit sectors. If the charging station is placed in a passage, two exit angles, for instance 70° - 110° and 250° - 290°, can be used.

When two exit angles are used, there is a need to also specify how often the robotic lawnmower must leave the charging station in sector 1. This is done using the Proportion function by initially specifying a percentage.

For instance the percentage of 75 % means that the robotic lawnmower leaves the charging station in Sector 1 on 75% of the times and 25% of the times in sector 2.

Use the number keys to specify the required angles in degrees for the sectors and proportion as a percentage.

Reversing distance

This functions allows you to control how far the robotic lawnmower has to reverse before it starts mowing. This is a useful function for instance if the charging station is placed way in under a veranda or in another limited space area.

Use the number keys to specify the required reverse distance in centimetres.

3012-1251

3012-1252

3012-1253

English - 57

Image 59

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Garden examples Maintenance Introduction and safety TroubleshootingTechnical Data Guarantee termsMEMO Introduction Introduction and safetySymbols on the product Text Important Information Text Symbols in the Operator’s ManualUse Safety instructionsMoving Maintenance Presentation Numbers in the illustration represent What is what?Capacity Package contentFunction Working method Mowing techniqueSearch method 1 Irregular Movement patternFinding the charging station Search method 3 Follow boundary wire Search method 2 Follow guide wirePreparations InstallationSee 7 Garden examples on page 65 for installation examples Best charging station location Installation of the charging station3012-559 Connecting the transformer Do not tread or walk on the charging station’s plate Installing and connecting the charging stationCharging the battery Plan where to lay the boundary wire Installation of the boundary wireWorking area boundaries Secondary areas Boundaries within the working areaSlopes Passages when mowingLaying the boundary wire Splicing the boundary wire Laying the boundary wire in towards the charging StationConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation Use Memo on page 2 to make a note of the PIN code First start-up and calibrationTest docking with the charging station Use Charging a flat batteryStarting Using the timerStopping Switching offAdjusting the cutting height Control panel Secondary area Operation selection StartMain area Operation selection Parking Charging station’s Park button Main switchNumber series Menu functionsMain menu Browse between menusMenu structure TimerCopy TimerAll week ResetOverview Current dayTo lower the cutting height Cutting heightTo increase the cutting height Time lock AlarmSecurity Function Low Medium HighChange PIN code New loop signalCustom Advanced Fault messagesMessages Info messages Weather timerReset messages Weather timerExample InstallationCutting time Boundary loop Guide Guide 1 delayGuide Guide 2 delay GuideOverview Test Setting RangeCharging station range Area Lawn coverageArea X How often? Area 1-5 How?Area X How far? This section does not apply to Automower GPSLawn coverage How far? ResetReset Current area Reset All areasCorridor width Boundary Corridor widthReversing distance Corridor width GuideExit angles Exit angles SectorsAutomatic passage handling Drive past wireInstallation shape Profiles SettingsSave settings to a Profile One Automower for several gardens Check New loop signal, See 6.5 Security on page 45Change the name of a profile Use a ProfilSpiral cutting Spiral cuttingCutting height calibration Time & DateCountry Select Reset all user settings in the menu and press OK Calibration of guide wireReset all user settings Mower house AccessoriesHeadlight Garden examples Installation proposals and settingsStation Installation proposals and settingsLawn coverage Find chargingGuide 1 Proportion 40% Guide 1 Proportion 60%As the GPS assisted navigation 3012-978 3018-095 Secondary area mode on Maintenance Charging station Winter storageRobotic lawnmower Chassis and blade disc Winter serviceCleaning After winter storageWheels Transport and movingEvent of a thunderstorm ChassisBlades BatteryFault messages TroubleshootingTroubleshooting Troubleshooting Info messages Light Cause Action Indicator lamp in the charging stationSymptoms Lawnmower mows Lawnmower runs, butBlade disc does Not rotateFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Data Technical DataGuarantee terms Environmental information EN 61000-6-3 emission EN 61000-6-1 immunity EC Declaration of ConformityOriginal Instructions