Husqvarna 320, 330X manual Installing and connecting the charging station

Page 21

INSTALLATION

Do not, under any circumstances, mount the transformer at a height where there is a risk it can be submerged in water (at least 30 cm from the ground). It is not permitted to place the transformer on the ground.

IMPORTANT INFORMATION

Use the transformer’s plug to disconnect the charging station, for instance before cleaning or repairing the loop wire.

Installing and connecting the charging station

1. Position the charging station in a suitable spot.

2. Tilt the protective cover on the charging station forward and connect the low voltage cable to the charging station.

3.Connect the transformer’s power cable to a 110- 230 V wall socket.

4. Attach the charging station to the ground using the supplied screws. Ensure the screws are screwed all the way down in the countersink. If the charging station is placed against a wall, it is best to wait before securing the charging station to the ground until after all the wires have been connected.

IMPORTANT INFORMATION

It is not permitted to make new holes in the charging station’s plate. Only the existing holes may be used to secure the base plate to the ground.

IMPORTANT INFORMATION

Do not tread or walk on the charging station’s plate.

3012-1090

3012-1093

3012-1063

3012-1045

English - 19

Image 21

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Technical Data Introduction and safety TroubleshootingGuarantee terms Garden examples MaintenanceMEMO Introduction Introduction and safetySymbols on the product Text Important Information Text Symbols in the Operator’s ManualUse Safety instructionsMoving Maintenance Presentation Numbers in the illustration represent What is what?Package content FunctionCapacity Working method Mowing techniqueMovement pattern Finding the charging stationSearch method 1 Irregular Search method 3 Follow boundary wire Search method 2 Follow guide wireInstallation See 7 Garden examples on page 65 for installation examplesPreparations Best charging station location Installation of the charging station3012-559 Connecting the transformer Do not tread or walk on the charging station’s plate Installing and connecting the charging stationCharging the battery Plan where to lay the boundary wire Installation of the boundary wireWorking area boundaries Secondary areas Boundaries within the working areaSlopes Passages when mowingLaying the boundary wire Splicing the boundary wire Laying the boundary wire in towards the charging StationConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation First start-up and calibration Test docking with the charging stationUse Memo on page 2 to make a note of the PIN code Use Charging a flat batteryStarting Using the timerSwitching off Adjusting the cutting heightStopping Control panel Operation selection Start Main areaSecondary area Operation selection Parking Charging station’s Park button Main switchMain menu Menu functionsBrowse between menus Number seriesMenu structure TimerCopy TimerOverview ResetCurrent day All weekCutting height To increase the cutting heightTo lower the cutting height Security AlarmFunction Low Medium High Time lockNew loop signal CustomChange PIN code Fault messages MessagesAdvanced Reset messages Weather timerWeather timer Info messagesInstallation Cutting timeExample Guide Guide 2 delay Guide Guide 1 delayGuide Boundary loopSetting Range Charging station rangeOverview Test Area Lawn coverageArea 1-5 How? Area X How far?Area X How often? This section does not apply to Automower GPSReset Current area ResetReset All areas Lawn coverage How far?Corridor width Boundary Corridor widthExit angles Corridor width GuideExit angles Sectors Reversing distanceDrive past wire Installation shapeAutomatic passage handling Settings Save settings to a ProfileProfiles Change the name of a profile Check New loop signal, See 6.5 Security on page 45Use a Profil One Automower for several gardensSpiral cutting Spiral cuttingTime & Date CountryCutting height calibration Calibration of guide wire Reset all user settingsSelect Reset all user settings in the menu and press OK Accessories HeadlightMower house Garden examples Installation proposals and settingsLawn coverage Installation proposals and settingsFind charging StationGuide 1 Proportion 60% As the GPS assisted navigationGuide 1 Proportion 40% 3012-978 3018-095 Secondary area mode on Maintenance Winter storage Robotic lawnmowerCharging station Cleaning Winter serviceAfter winter storage Chassis and blade discEvent of a thunderstorm Transport and movingChassis WheelsBlades BatteryFault messages TroubleshootingTroubleshooting Troubleshooting Info messages Light Cause Action Indicator lamp in the charging stationSymptoms Blade disc does Lawnmower runs, butNot rotate Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Data Technical DataGuarantee terms Environmental information EN 61000-6-3 emission EN 61000-6-1 immunity EC Declaration of ConformityOriginal Instructions