Husqvarna 330X, 320 manual Info messages

Page 80

TROUBLESHOOTING

9.2 Info messages

A number of info messages are listed below that can be shown on the display on the robotic lawnmower. It is recommended to contact your dealer if the same message appears often. Check that the installation is performed as described in the Operator’s Manual. Then contact your local dealer.

Message	Cause	Action
Low battery	The robotic lawnmower cannot find the	Check that the charging station and the guide wire
	charging station.	are installed in accordance with the instructions.
		See 3 Installation on page 15.
	The guide wire is broken or not	Find out where the break is and rectify it.
	connected.
	The battery is spent.	Contact your dealer to test or possibly replace the
		battery.
	The charging station’s antenna is	Check if the indicator lamp in the charging station
	defective.	flashes red. See 9.3 Indicator lamp in the charging
		station on page 79.
Settings restored	Confirmation that a Reset all user	This is normal. No action required.
	settings has been carried out.
Slope too steep	The robotic lawnmower is in an area	Isolate the very steep part of the working area
	that exceeds the maximum permitted	so that no part of the working area exceeds the
	slope.	specifications for the robotic lawnmower.
Limited cutting height	The maximum and minimum position	Check that there no grass or other objects are
range	of the cutting height adjustment is	blocking the blade disc from moving up or down.
	limited.	Carry out a cutting height calibration using the
		Settings > Cutting height menu.
		Contact your dealer if the message appears often.
Unexpected cutting	The cutting height adjustment is	Carry out a cutting height calibration via the
height adj	altered without a request from the	Settings > Cutting height menu.
	robotic lawnmower.	Contact your dealer if the message appears often.
No response from	Communication problems between	Remove the robotic lawnmower from the charging
charger	the robotic lawnmower and charging	station and put it back again. Check that there is
	station.	good contact between the charging strips on the
		lawnmower and the charging station.
		Contact your dealer if the message appears often.
Guide 1 not found	The guide wire is not connected to the	Check that the guide wire’s connector is tightly
Guide 2 not found	charging station	connected to the charging station. See 3.6
		Installation of the guide wire on page 28.
	Break in the guide wire	Find out where the break is. Replace the damaged
		section of the guide wire with a new loop wire and
		splice using an original coupler.
	The guide wire is not connected to the	Check that the guide wire is connected correctly to
	boundary loop.	the boundary loop. See 3.6 Installation of the guide
		wire on page 28. Splice using an original coupler.
GPS navigation	Problem with the GPS assisted	Contact your dealer if the message appears often.
problem	navigation equipment.

English - 78

Image 80

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Introduction and safety Troubleshooting Technical DataGuarantee terms Garden examples MaintenanceMEMO Introduction and safety IntroductionSymbols on the product Symbols in the Operator’s Manual Text Important Information TextSafety instructions UseMoving Maintenance Presentation What is what? Numbers in the illustration representCapacity Package contentFunction Mowing technique Working methodSearch method 1 Irregular Movement patternFinding the charging station Search method 2 Follow guide wire Search method 3 Follow boundary wirePreparations InstallationSee 7 Garden examples on page 65 for installation examples Installation of the charging station Best charging station location3012-559 Connecting the transformer Installing and connecting the charging station Do not tread or walk on the charging station’s plateCharging the battery Installation of the boundary wire Plan where to lay the boundary wireWorking area boundaries Boundaries within the working area Secondary areasPassages when mowing SlopesLaying the boundary wire Laying the boundary wire in towards the charging Station Splicing the boundary wireConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation Use Memo on page 2 to make a note of the PIN code First start-up and calibrationTest docking with the charging station Charging a flat battery UseUsing the timer StartingStopping Switching offAdjusting the cutting height Control panel Secondary area Operation selection StartMain area Operation selection Parking Main switch Charging station’s Park buttonMenu functions Main menuBrowse between menus Number seriesTimer Menu structureTimer CopyReset OverviewCurrent day All weekTo lower the cutting height Cutting heightTo increase the cutting height Alarm SecurityFunction Low Medium High Time lockChange PIN code New loop signalCustom Advanced Fault messagesMessages Weather timer Reset messagesWeather timer Info messagesExample InstallationCutting time Guide Guide 1 delay Guide Guide 2 delayGuide Boundary loopOverview Test Setting RangeCharging station range Lawn coverage AreaArea X How often? Area 1-5 How?Area X How far? GPS This section does not apply to AutomowerReset Reset Current areaReset All areas Lawn coverage How far?Corridor width Corridor width BoundaryCorridor width Guide Exit anglesExit angles Sectors Reversing distanceAutomatic passage handling Drive past wireInstallation shape Profiles SettingsSave settings to a Profile Check New loop signal, See 6.5 Security on page 45 Change the name of a profileUse a Profil One Automower for several gardensSpiral cutting Spiral cuttingCutting height calibration Time & DateCountry Select Reset all user settings in the menu and press OK Calibration of guide wireReset all user settings Mower house AccessoriesHeadlight Installation proposals and settings Garden examplesInstallation proposals and settings Lawn coverageFind charging StationGuide 1 Proportion 40% Guide 1 Proportion 60%As the GPS assisted navigation 3012-978 3018-095 Secondary area mode on Maintenance Charging station Winter storageRobotic lawnmower Winter service CleaningAfter winter storage Chassis and blade discTransport and moving Event of a thunderstormChassis WheelsBattery BladesTroubleshooting Fault messagesTroubleshooting Troubleshooting Info messages Indicator lamp in the charging station Light Cause ActionSymptoms Lawnmower runs, but Blade disc doesNot rotate Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Technical Data DataGuarantee terms Environmental information EC Declaration of Conformity EN 61000-6-3 emission EN 61000-6-1 immunityOriginal Instructions