Husqvarna 320, 330X manual Security, Function Low Medium High, Time lock, PIN request, Alarm

Page 47

MENU FUNCTIONS

6.5 Security

Through this selection, settings relating to security and the connection between the robotic lawnmower and the charging station can be made.

There are three security levels to choose from but it is also possible to define your own combination of security functions.

The factory setting is security level Medium.

Use the down and up arrow keys to select a security level.

Low and medium security prohibits access to the robotic lawnmower if the PIN code is unknown. High security also includes a warning that beeps if the correct PIN code is not entered after a designated time period.

Function	Low	Medium	High

Time lock	X	X	X

PIN request		X	X

Alarm			X

Time lock

This function means that the robotic lawnmower cannot be started after 30 days without first entering the correct PIN code. When the 30 days has passed the robotic lawnmower will continue to mow as normal, but the Enter PIN code message appears when the hatch is opened. Enter your code again and press OK.

After this, the selected PIN code must be entered every time the main switch is set to 1.

PIN request

This function means that the robotic lawnmower requests a PIN code each time the hatch is opened. The correct PIN code must be entered to use the robotic lawnmower.

If the wrong PIN code is entered 5 times in succession the robotic lawnmower is blocked for a time. The blockage time is extended for every new incorrect attempt.

Alarm

This function means that an alarm sounds if the PIN code is not entered within 10 seconds after the STOP button has been pressed or the robotic lawnmower has been lifted up for any reason. A ticking noise indicates that the PIN code must be entered to prevent triggering the alarm. The alarm can be turned off at any time by entering the correct PIN code.

Security

Security		Change		New		Advanced Reset security
level		PIN Code		loop signal				settings


					Duration		Duration of
					of alarm		time lock


Low		Medium		High		Custom

3012-1237

English - 45

Image 47

Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Garden examples Maintenance Introduction and safety TroubleshootingTechnical Data Guarantee termsMEMO Introduction Introduction and safetySymbols on the product Text Important Information Text Symbols in the Operator’s ManualUse Safety instructionsMoving Maintenance Presentation Numbers in the illustration represent What is what?Capacity Package contentFunction Working method Mowing techniqueSearch method 1 Irregular Movement patternFinding the charging station Search method 3 Follow boundary wire Search method 2 Follow guide wirePreparations InstallationSee 7 Garden examples on page 65 for installation examples Best charging station location Installation of the charging station3012-559 Connecting the transformer Do not tread or walk on the charging station’s plate Installing and connecting the charging stationCharging the battery Plan where to lay the boundary wire Installation of the boundary wireWorking area boundaries Secondary areas Boundaries within the working areaSlopes Passages when mowingLaying the boundary wire Splicing the boundary wire Laying the boundary wire in towards the charging StationConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation Use Memo on page 2 to make a note of the PIN code First start-up and calibrationTest docking with the charging station Use Charging a flat batteryStarting Using the timerStopping Switching offAdjusting the cutting height Control panel Secondary area Operation selection StartMain area Operation selection Parking Charging station’s Park button Main switchNumber series Menu functionsMain menu Browse between menusMenu structure TimerCopy TimerAll week ResetOverview Current dayTo lower the cutting height Cutting heightTo increase the cutting height Time lock AlarmSecurity Function Low Medium HighChange PIN code New loop signalCustom Advanced Fault messagesMessages Info messages Weather timerReset messages Weather timerExample InstallationCutting time Boundary loop Guide Guide 1 delayGuide Guide 2 delay GuideOverview Test Setting RangeCharging station range Area Lawn coverageArea X How often? Area 1-5 How?Area X How far? This section does not apply to Automower GPSLawn coverage How far? ResetReset Current area Reset All areasCorridor width Boundary Corridor widthReversing distance Corridor width GuideExit angles Exit angles SectorsAutomatic passage handling Drive past wireInstallation shape Profiles SettingsSave settings to a Profile One Automower for several gardens Check New loop signal, See 6.5 Security on page 45Change the name of a profile Use a ProfilSpiral cutting Spiral cuttingCutting height calibration Time & DateCountry Select Reset all user settings in the menu and press OK Calibration of guide wireReset all user settings Mower house AccessoriesHeadlight Garden examples Installation proposals and settingsStation Installation proposals and settingsLawn coverage Find chargingGuide 1 Proportion 40% Guide 1 Proportion 60%As the GPS assisted navigation 3012-978 3018-095 Secondary area mode on Maintenance Charging station Winter storageRobotic lawnmower Chassis and blade disc Winter serviceCleaning After winter storageWheels Transport and movingEvent of a thunderstorm ChassisBlades BatteryFault messages TroubleshootingTroubleshooting Troubleshooting Info messages Light Cause Action Indicator lamp in the charging stationSymptoms Lawnmower mows Lawnmower runs, butBlade disc does Not rotateFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Data Technical DataGuarantee terms Environmental information EN 61000-6-3 emission EN 61000-6-1 immunity EC Declaration of ConformityOriginal Instructions