Husqvarna 330X, 320 manual Using the timer, Starting

Page 36

USE

4.2 Using the timer

The lawn should not be cut too often to obtain the best mowing result. Use the timer function (see 6.3 Timer on page 42) to avoid a downtrodden lawn and to get the maximum service life from the robotic lawnmower. When setting the timer, calculate that the robotic lawnmower mows about 135 m2 per hour and day (90 m2 for Automower® 320). For example; If the working area is 1,200 m2 the robotic lawnmower must operate for about 9 hours per day (13 hours for Automower® 320). The times are approximate and depend for instance on grass quality, blade sharpness and battery age.

IMPORTANT INFORMATION

Use the timer to avoid mowing when there are usually children, pets and anything else about that could be hurt or damaged by the rotating blades on the lawn.

The factory setting is that the robotic lawnmower will operate around the clock seven days a week.

If the size of the working area allows it, the quality of the grass can be further improved if it is cut every other day instead of a few hours every day. In addition, the grass benefits from resting completely during at least a three- day period once a month.

The maximum capacity, 3200 m2 for Automower® 330X and 2200 m2 for Automower® 320, is only obtained when the robotic lawnmower is allowed to mow around the clock seven days a week.

4.3Starting

1.Press the STOP button to open the control panel

hatch.

2. Set the main switch to position 1.

3.Enter the PIN code.

The PIN code request can be disabled. See 6.5 Security on page 45 for more information on theft

protection.

3012-1204

4.Push the Start button.

5.Make the required operation selection. See 5.1 Operation selection Start on page 37.

6.Shut the hatch within 10 seconds.

If the robotic lawnmower is parked in the charging station, it will only leave the charging station when the battery is fully charged and if the timer is set to allow the mower to operate.

Before the blade disc starts a warning beep can be heard consisting of 5 short beeps for 2 seconds.

English - 34

Image 36
Contents Husqvarna Automower 320/330X OPERATOR’S Manual Page Introduction and safety Troubleshooting Technical DataGuarantee terms Garden examples MaintenanceMEMO Introduction and safety IntroductionSymbols on the product Symbols in the Operator’s Manual Text Important Information TextSafety instructions UseMoving Maintenance Presentation What is what? Numbers in the illustration representPackage content FunctionCapacity Mowing technique Working methodMovement pattern Finding the charging stationSearch method 1 Irregular Search method 2 Follow guide wire Search method 3 Follow boundary wireInstallation See 7 Garden examples on page 65 for installation examplesPreparations Installation of the charging station Best charging station location3012-559 Connecting the transformer Installing and connecting the charging station Do not tread or walk on the charging station’s plateCharging the battery Installation of the boundary wire Plan where to lay the boundary wireWorking area boundaries Boundaries within the working area Secondary areasPassages when mowing SlopesLaying the boundary wire Laying the boundary wire in towards the charging Station Splicing the boundary wireConnecting the boundary wire Installation of the guide wire Laying and connecting the guide wire 135º 90º 3018-061 3012-953 3012-954 3018-055 Checking the installation First start-up and calibration Test docking with the charging stationUse Memo on page 2 to make a note of the PIN code Charging a flat battery UseUsing the timer StartingSwitching off Adjusting the cutting heightStopping Control panel Operation selection Start Main areaSecondary area Operation selection Parking Main switch Charging station’s Park buttonMenu functions Main menuBrowse between menus Number seriesTimer Menu structureTimer CopyReset OverviewCurrent day All weekCutting height To increase the cutting heightTo lower the cutting height Alarm SecurityFunction Low Medium High Time lockNew loop signal CustomChange PIN code Fault messages MessagesAdvanced Weather timer Reset messagesWeather timer Info messagesInstallation Cutting timeExample Guide Guide 1 delay Guide Guide 2 delayGuide Boundary loopSetting Range Charging station rangeOverview Test Lawn coverage AreaArea 1-5 How? Area X How far?Area X How often? GPS This section does not apply to AutomowerReset Reset Current areaReset All areas Lawn coverage How far?Corridor width Corridor width BoundaryCorridor width Guide Exit anglesExit angles Sectors Reversing distanceDrive past wire Installation shapeAutomatic passage handling Settings Save settings to a ProfileProfiles Check New loop signal, See 6.5 Security on page 45 Change the name of a profileUse a Profil One Automower for several gardensSpiral cutting Spiral cuttingTime & Date CountryCutting height calibration Calibration of guide wire Reset all user settingsSelect Reset all user settings in the menu and press OK Accessories HeadlightMower house Installation proposals and settings Garden examplesInstallation proposals and settings Lawn coverageFind charging StationGuide 1 Proportion 60% As the GPS assisted navigationGuide 1 Proportion 40% 3012-978 3018-095 Secondary area mode on Maintenance Winter storage Robotic lawnmowerCharging station Winter service CleaningAfter winter storage Chassis and blade discTransport and moving Event of a thunderstormChassis WheelsBattery BladesTroubleshooting Fault messagesTroubleshooting Troubleshooting Info messages Indicator lamp in the charging station Light Cause ActionSymptoms Lawnmower runs, but Blade disc doesNot rotate Lawnmower mowsFinding breaks in the loop wire 3012-1208 3018-053 3018-055 Technical Data DataGuarantee terms Environmental information EC Declaration of Conformity EN 61000-6-3 emission EN 61000-6-1 immunityOriginal Instructions