Manuals / 3Com / Computer Equipment / Switch

3Com S200 manual #12, PAD Data Restraint, #13, Line Feed Insertion after CR

Models: S200

1 85

Download 85 pages 18.3 Kb

Page 39

#12, PAD Data Restraint

PAD Profile Table Record

#12, PAD Data Restraint

Range:	0, 1

Default:	1

Description:	Specifies if and how the XON/XOFF characters sent from the
	attached terminal restrain the PAD from sending data:
	• 0: No flow control with XON/XOFF
	• 1: Allow flow control on outbound data and service signals
	For DRO control using V.24 connector control signals (pin 14):
	• Set this parameter to 0.
	• Use parameter #105, Control Signal (EIA-232-D) Data
	Restraint.
	• Called Data Restraint Outbound (DRO) when using inband
	control.

#13, Line Feed Insertion after CR

Range:	0 to 7
Default:	4

Description:	Determines if and how a line feed character is inserted into the
	data during Data Mode:

•0: Line feed is not inserted.

•1: Line feed is inserted after <CR> in data sent to device.

•2: Line feed is inserted after <CR> in data from attached device.

•4: Line feed is inserted after echo of <CR> to attached device.

•X: Any combination of the above, for example, to combine 1 and 2, enter 3.

Configuring PAD/ATPAD Ports

33

Image 39

3Com S200 manual #12, PAD Data Restraint, #13, Line Feed Insertion after CR

Contents

3Com Corporation PathBuilder S200 Series Switch Configuring with PAD/ATPADRestricted Rights Legend Restricted Rights Notification for U.S. Government UsersProprietary Material Notice continuedPage Contents Page Before You Begin Configuring PAD/ATPAD PortsOverview IntroductionFeatures What is a PAD?What Is a PAD What is an ATPADFigure 1. Topologies with and Without the PAD Typical ApplicationsExample IntroductionRecord PAD Port ConfigurationConfiguration PAD PortGuidelines If You Specify or SetThen Result RecordStep ActionIntroduction ParametersConnection Type Configuring the PAD PortWhen... continued Port ControlAuto Baud Sequence Port SpeedProfile Name Data Bits per CharacterDevice Parity Number of Stop BitsCall Control Terminal Control Autocall Mnemonic Autocall Timeout secPAD Prompt Entry Number Remote PAD Parameters NumberCUG Membership Maximum Number of Autocall AttemptsSubaddress Group SubaddressCall Accept Timeout sec Billing RecordsInvitation to clear Reconnection Timeout Protection LevelReconnection Tries Limit Calling DTE Identifier Calling DTE PasswordMaximum Receive Buffer Length Called DTE AddressMax NUI violations PAD Command LanguageNUI verification timer NUI Facility FormatAction Type for NUI violations PAD Port Configuration for Autocalling Initiating an AutoCall Mnemonic AddressingIntroduction Figure 3. SDLC Mnemonic Autocall Addressing SDLC Mnemonic AddressingAutospeed PAD Port Configuration for AutospeedCharacter Delay ImplementingHow It Works PAD XON/OFF Support Using X.25 Interrupt Packets4 Perform a Node boot to implement your changes To enable this CSK Complete these steps to enable the XON/XOFF CSK1 Select Configure from the CTP Main menu 2 Select Software Key Table from the Configure menuThis Record Before You Begin Accessing the PAD Prompt Table RecordPAD Prompt Table Record What You See inIntroduction PAD Prompt Table Record ParametersEntry Number PAD Prompt TextIntroduction What You See In This Record PAD Profile Table RecordStep Configuration GuidelinesAccessing the PAD Profile Table Record Select PAD Profile Table fromParameters PAD Profile Table Record Parameters#1, PAD Recall Introduction#4, Idle Timer Delay #2, Echo#3, Data Forwarding Character #5, Device Flow Control #6, Service Signals Control#7, Break Signal Operation #9, Padding After Carriage Return#10, Line Folding #13, Line Feed Insertion after CR #12, PAD Data Restraint#17, Line Delete #14, Padding after LF#15, Editing #16, Character Delete#19, Editing Type #18, Line Display#21 Parity Treatment #20, Echo Mask#102, Echo Substitution Character #22, Page Wait#100, Break Character #101, Echo Substitution Toggle Character#105, Control Signal EIA-232-D Data Restraint #103, XON Character#104, XOFF Character #107, Idle Disconnect Timer #106, Network Parity#108, Disconnect Character #109, Form Feed Padding #110, Esc Forwarding Delay Handling#111, Echo Control #112, Dynamic Data Forwarding#113, Hewlett-Packard Flow Control #114, PAD Mode #116, Short Timer Duration#115, Data Forwarding Criteria #117, EIA Signalling Action #118, Message Assembly#119, DCD to Data Timer Duration Profile Table Copying PAD Profile Tables into a ConfigurationPAD Profile Table SizeTest Parameter Values Stored In MemoryDefault Parameter NameParameter Values Stored in Memory Parameter Values Stored In Memory continuedParameter Values Stored in Memory continued Message Parameter 6 service signals control is set to90 and PAD BulletinParameter Table Record Before You Begin Configuration Guidelines Accessing the Remote PADRemote PAD Parameter Table Record What You See InEntry Number Remote PAD Parameter Table Record ParametersIntroduction Parameters#1 Parameter Number #1 Parameter Number continued #1 Parameter ValueExample Detailed PAD Port Statistics FunctionDescription of Terms - First Screen Data Summary IN/OUT Description of Terms - Second Screen Screen TermTells You Figure 11. Example of Detailed PAD Port Statistics, Third Screen ATPAD Ports ATPAD Portshow to configure them IntroductionATPAD Operation ATPAD Data Forwarding CriteriaCriteria Descriptions Flow Control You can configure the ATPAD for either type of flow controlFigure 12. ATPAD Application Environment Network Parity Application Response Delay DTR TimeoutConfiguration Use these guidelines when you enter ATPAD commandsGuidelines Figure 13. Configure ATPAD Port Menu Configuring PAD/ATPAD PortsATPAD Ports Connection Type Port TypeClock Speed ParametersEscape Character Data BitsParity Stop BitsData Forwarding Character Carriage Return CharacterLine Feed Character Back Space CharacterFlow Control Escape Sequence TimerData Forwarding Timer XON CharacterStored Addresses Answer ModePacket Size EchoBilling Records Result CodesRestricted Connection Destination Port AddressProtocol ID Network ParityRange Characters/sec ATPAD Port StatisticsFunction Description of Terms - First ScreenScreen Term Tells You... continuedFigure 15. ATPAD Port Statistics - Screen Description of Terms - Second Screen Screen TermTells You World Wide Web ServicesTechnical Support Online Technical1 408 654 Access by Analog Modem3ComFacts Automated Fax Service Support from Your Network Supplier Access by Digital ModemEurope Support from3Com Asia Pacific RimReturning Symbols IndexNumerics