General | Actiontec electronic MI424-WR specification

Chapter 5 Using Network Connections

Configure Coax

Click Settings at the bottom-right of the Coax Properties screen generates the “Configure Coax” screen.

General

The top part of the Configure Coax screen displays general communication parameters. Actiontec recommends not changing the default values in this sec- tion unless familiar with networking concepts.

Status Displays the status of the coax connection.v

When should this rule occur? Displays when the rule is active. To schedule rules, see the “Advanced Settings” chapter

Network Displays the type of network.

Connection Type Displays the type of connection.

Physical Address Displays the physical address of the network card used for the network.

MTU MTU (Maximum Transmission Unit) specifies the largest packet size per- mitted for Internet transmission. “Automatic” sets the MTU at 1500. Other choic- es include “Automatic by DHCP,” which sets the MTU according to the DHCP connection, and “Manual,” which allows the MTU to be set manually.

57

Image 62

Actiontec electronic MI424-WR user manual General

Contents

Wireless Broadband Router Table of Contents Troubleshooting 147 Quality of Service 151 Using Parental Controls 101Using Advanced Settings 109 Monitoring the Router 143 169 Specifications 167Limited Warranty 171 This page left intentionally blank Package Contents Introduction1 Minimum System Requirements FeaturesWall-mount template Vertical stand Warranty Intrusion detection MAC address filtering Power Light Getting to Know the Router Coax WAN Light Wireless LightEthernet WAN Light Internet Light Coax Port Reset ButtonRear Panel Power Port Power SwitchPower switch powers the Router on and off Ethernet WAN Port This page left intentionally blank Connecting Router Setting Up the Router Then press Enter on the keyboard Router is now configured Connecting the Router Wireless Ethernet Windows XP Computer Network ConfigurationCoaxial Windows NT WindowsWindows 98/Me Home Linux Action Zone Broadband ConnectionQuick Links Configuring My Network Settings Accessing My Network Using My Network Configuring My Network Settings Page Configuring My Network Settings Enable Application Click Add. The Add Port Forwarding Rule screen appears Configuring My Network Settings Page Configuring My Network Settings This page left intentionally blank Creating a Wireless Network Overview Wireless Status Channel Creating a Wireless Network Basic Security Settings Click Apply to save the settings Advanced Security Settings Level 1 Wireless Security WEP Click Apply to save changes 802.1X WEP WPA Select the proper encryption algorithm Tkip or AESPage Wireless MAC Authentication When should this rule occur? 802.11b/g ModeAdvanced Wireless Options Transmission Rate CTS Protection ModeNetwork Beacon Interval RTS Threshold Configuring a Wireless Windows XP ClientFragmentation Threshold Creating a Wireless Network Connecting a Wireless Windows XP Client Creating a Wireless Network Page Creating a Wireless Network This page left intentionally blank Using Network Connections Network Home/Office General Internet Protocol Bridge DNS Server IP Address Distribution Routing Additional IP Addresses Ethernet ConnectionRouting Table General Ports Ethernet Switch Coax Connection General Coax Connection Status Password Enter the Coax Link password in this text boxCoax Link Broadband Ethernet Connection Configuring the Broadband Ethernet Connection Internet Protocol IP Address Distribution Routing Coax Broadband Connection Internet Connection Firewall Configuring the Coax Broadband Connection This section displays the Router’s Tx and Rx speeds in Mbps Password Enter the Coax Link password hereWAN Coax Connection Speeds DNS Server Routing WAN PPPoE/WAN PPPoE General PPP session automatically ends PPP ConfigurationPPP Authentication PPP reconnect attempts, as provided by the ISP PPP Compression Internet Protocol Routing Table Configuring Router’s Security Page General Limited Only commonly Configured in the AccessSecurity Level Incoming traffic Network outgoing traffic Network from Internet Access Control Page Configuring the Router’s Security Port Forwarding DMZ Demilitarized Zone Host Click Apply to save the changes Port Triggering Configuring the Router’s Security Remote Administration Configuring the Router’s Security Website Blocking Click Apply to save changes Static NAT Advanced Filtering Page Configuring the Router’s Security Security Log Configuring the Router’s Security Page Configuring the Router’s Security Page Configuring the Router’s Security 100 Using Parental Controls Activating Parental Controls Creating a Filtering Policy Parental Controls Websites and URL Filtering 105 Advanced Options Statistics 108 Using Advanced Settings 110 Firmware Upgrade 111 Automatically Check and Send E-mail Automatically Check and UpgradeUpgrading From the Internet Manual Checking and Upgrading Firmware RestoreAutomatic Check Disabled Configuration File System Settings Warn User Before Network Configuration Changes Wireless Broadband Router’s HostnamePrompt for Password When Accessing via LAN Local Domain Allowed Capacity Before Email Notification Enable LoggingLow Capacity Notification Enabled System Log Buffer Size Enter the size of the security log buffer in this text box Click in this check box to activate security loggingSecurity Log Buffer Size Server Dhcp Timeout Server Requires AuthenticationPPP Timeout Port Date and Time Scheduler Rules 122 Routing 124 IP Address Distribution Domain Routing 126 127 128 Diagnostics Restoring Default Settings Reboot the Router ARP Address Resolution Protocol Table MAC Cloning Users Local Administration QoS Dynamic DNS Offline Connection To UpdatePassword User Name Host Name Backup MXDNS Server Wildcard 137 Network Objects Universal Plug and Play UPnP 140 Protocols 141 142 Monitoring Router Router Status System Log Connection Monitoring Traffic Monitoring Restoring the Router’s Default Settings TroubleshootingAccessing the Router if Locked Out LAN Connection Failure Time out error occurs when entering a URL or IP AddressIs the wireless option on by default on the Router? Ensure the Subnet Mask address is set to No. Follow these steps to refresh the IP address How do I find out what IP address my computer is using?Are the Router’s Ethernet ports auto-sensing? What is the default user name for the Router? How many computers can be connected through the Router? 802.1p Priority Quality of ServiceTraffic Priority MSN Messenger/Windows Messenger 323 Port triggering applications Appendix a Quality of Service 154 Traffic Shaping 156 157 To define a shaping class Name the new class and click Apply 159 160 161 162 163 802.1p Settings 165 166 Specifications B Environmental Wireless Operating RangeLED Indicators Class B Equipment Regulatory Compliance NoticesModifications 170 Limited Warranty 171 172 Limited Warranty 174