Manuals / Actiontec electronic / Computer Equipment / Network Router

Actiontec electronic MI424-WR user manual PPP Configuration, PPP session automatically ends

Models: MI424-WR

1 179

Download 179 pages 51.83 Kb

Page 76

Chapter 5 Using Network Connections

Network Select the type of connection being configured from the drop-down list (Broadband Connection, Network (Home/Office), or DMZ).

Connection Type Displays the type of connection. Since this is PPPoE connection, “PPPoE” is displayed.

MTU MTU (Maximum Transmission Unit) specifies the largest packet size permitted for Internet transmission. “Automatic, sets the MTU at 1492. Other choices include “Automatic,” which sets the MTU according to the connection to the ISP, and “Manual,” which allows the MTU to be set manually.

Underlying Connection Specify the underlying connection above which the proto- col initiates from the drop-down list, which displays all possible underlying devices.

PPP Configuration

Point-to-Point Protocol (PPP) is the most popular method for transporting packets between the user and the ISP.

Service Name Specify the networking peer’s service name, if provided by the ISP, in this text box.

On-Demand To use PPP on demand to initiate the point-to-point protocol session only when packets are actually sent over the Internet, click in this check box. This option should be active on a limited basis

Idle Time Before Hanging Up Enter the amount of idle time, in minutes, before the

PPPsession automatically ends .

Time Between Reconnect Attempts In this text box, specify the duration between

PPPreconnect attempts, as provided by the ISP.

PPP Authentication

Point-to-Point Protocol (PPP) currently supports four authentication pro- tocols: Password Authentication Protocol (PAP), Challenge Handshake Authentication Protocol (CHAP), and Microsoft CHAP versions 1 and 2. Select the authentication protocols the Router may use when negotiating with a PPTP server in this section. Select all the protocols if no information is available about the server’s authentication methods. Note that encryption is performed only if Microsoft CHAP, Microsoft CHAP version 2, or both are selected.

MWarning: The PPP Authentication settings should not be changed unless instructed to do so by Verizon.

71

Image 76

Actiontec electronic MI424-WR user manual PPP Configuration, PPP session automatically ends, PPP Authentication

Contents

Wireless Broadband Router Table of Contents Using Parental Controls 101 Using Advanced Settings 109Troubleshooting 147 Quality of Service 151 Monitoring the Router 143Limited Warranty 171 Specifications 167169 This page left intentionally blank Package Contents Introduction1Wall-mount template Vertical stand Warranty FeaturesMinimum System Requirements Intrusion detection MAC address filtering Power Light Getting to Know the RouterWireless Light Ethernet WAN LightCoax WAN Light Internet LightRear Panel Reset ButtonCoax Port Power Switch Power switch powers the Router on and offPower Port Ethernet WAN PortThis page left intentionally blank Connecting Router Setting Up the RouterThen press Enter on the keyboard Router is now configured Connecting the RouterWireless EthernetCoaxial Computer Network ConfigurationWindows XP Windows 98/Me WindowsWindows NT Home LinuxQuick Links Broadband ConnectionAction Zone Configuring My Network Settings Accessing My NetworkUsing My Network Configuring My Network Settings Page Configuring My Network Settings Enable Application Click Add. The Add Port Forwarding Rule screen appearsConfiguring My Network Settings Page Configuring My Network Settings This page left intentionally blank Creating a Wireless Network OverviewWireless Status ChannelCreating a Wireless Network Basic Security Settings Click Apply to save the settings Advanced Security Settings Level 1 Wireless SecurityWEP Click Apply to save changes802.1X WEP WPA Select the proper encryption algorithm Tkip or AESPage Wireless MAC Authentication Advanced Wireless Options 802.11b/g ModeWhen should this rule occur? CTS Protection Mode NetworkTransmission Rate Beacon IntervalFragmentation Threshold Configuring a Wireless Windows XP ClientRTS Threshold Creating a Wireless Network Connecting a Wireless Windows XP Client Creating a Wireless Network Page Creating a Wireless Network This page left intentionally blank Using Network Connections Network Home/Office General Internet Protocol BridgeDNS Server IP Address DistributionRouting Routing Table Ethernet ConnectionAdditional IP Addresses General Ports Ethernet Switch Coax Connection General Coax Link Password Enter the Coax Link password in this text boxCoax Connection Status Broadband Ethernet Connection Configuring the Broadband Ethernet Connection Internet Protocol IP Address Distribution Routing Coax Broadband Connection Internet Connection FirewallConfiguring the Coax Broadband Connection WAN Coax Connection Speeds Password Enter the Coax Link password hereThis section displays the Router’s Tx and Rx speeds in Mbps DNS Server Routing WAN PPPoE/WAN PPPoE General PPP Configuration PPP AuthenticationPPP session automatically ends PPP reconnect attempts, as provided by the ISPPPP Compression Internet Protocol Routing Table Configuring Router’s Security Page General Configured in the Access Security Level Incoming traffic Network outgoing trafficLimited Only commonly Network from InternetAccess Control Page Configuring the Router’s Security Port Forwarding DMZ Demilitarized Zone Host Click Apply to save the changesPort Triggering Configuring the Router’s Security Remote Administration Configuring the Router’s Security Website Blocking Click Apply to save changes Static NAT Advanced Filtering Page Configuring the Router’s Security Security Log Configuring the Router’s Security Page Configuring the Router’s Security Page Configuring the Router’s Security 100 Using Parental Controls Activating Parental ControlsCreating a Filtering Policy Parental Controls Websites and URL Filtering 105 Advanced Options Statistics 108 Using Advanced Settings 110 Firmware Upgrade 111Upgrading From the Internet Automatically Check and UpgradeAutomatically Check and Send E-mail Automatic Check Disabled Firmware RestoreManual Checking and Upgrading Configuration File System Settings Wireless Broadband Router’s Hostname Prompt for Password When Accessing via LANWarn User Before Network Configuration Changes Local DomainEnable Logging Low Capacity Notification EnabledAllowed Capacity Before Email Notification System Log Buffer SizeClick in this check box to activate security logging Security Log Buffer SizeEnter the size of the security log buffer in this text box ServerServer Requires Authentication PPP TimeoutDhcp Timeout PortDate and Time Scheduler Rules 122 Routing 124 IP Address Distribution Domain Routing126 127 128 Diagnostics Restoring Default Settings Reboot the RouterARP Address Resolution Protocol Table MAC CloningUsers Local Administration QoSDynamic DNS Connection To Update PasswordOffline User NameBackup MX DNS ServerHost Name Wildcard137 Network Objects Universal Plug and Play UPnP 140 Protocols 141142 Monitoring Router Router StatusSystem Log Connection Monitoring Traffic Monitoring Accessing the Router if Locked Out TroubleshootingRestoring the Router’s Default Settings Time out error occurs when entering a URL or IP Address Is the wireless option on by default on the Router?LAN Connection Failure Ensure the Subnet Mask address is set toAre the Router’s Ethernet ports auto-sensing? How do I find out what IP address my computer is using?No. Follow these steps to refresh the IP address What is the default user name for the Router? How many computers can be connected through the Router?Traffic Priority Quality of Service802.1p Priority MSN Messenger/Windows Messenger 323 Port triggering applicationsAppendix a Quality of Service 154 Traffic Shaping 156 157 To define a shaping class Name the new class and click Apply159 160 161 162 163 802.1p Settings 165 166 Specifications B LED Indicators Wireless Operating RangeEnvironmental Modifications Regulatory Compliance NoticesClass B Equipment 170 Limited Warranty 171172 Limited Warranty 174