DSR Options | ADTRAN ISU 512 instruction

Chapter 5: Configuration

3=CONFIG 2=DTE options

7=DTR Options 1=Ignore DTR (default) 2=Idle when Off 3=Off>On dial #0 4=Dial #0 if On 5=Answer if On

To store a number for automatic dialing see Dialing Options. Selecting Dial #0 if On allows calls to be automatically established when the DTR signal is in the active state. The unit attempts to establish a call using SN0-SN4 until the call is established or DTR goes inactive. Selecting Answer if On allows the unit to answer an incoming call only if the DTR signal is asserted.

During dual-port mode, if DTR options is set to Idle when off, dropping DTR on the V.35 port terminates both calls; dropping DTR on the RS-530 port terminates only the call on the RS-530 port.

DSR Options

Selecting DSR forced on causes the DSR signal on the DTE connector to al- ways be asserted. Selecting OFF Idle + Test causes DSR to be disasserted if the network interface is in test or there is not an active call. OFF Link Down causes DSR to be disasserted if the network interface is disrupted. Use the fol- lowing menu path to set DSR Options:

3=CONFIG 2=DTE options

8=DSR Options

1=DSR forced on (default) 2=OFF Idle+Test 3=OFF Link Down

61202.086L1-1

ISU 512 User Manual

45

Image 61

ADTRAN ISU 512 user manual DSR Options

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status Main Menu Menu StructureLCD Display of the Main Menu Status Menu Basic Menu Traversal ISU 512 Front View Front Panel Numeric Keypad LCD WindowUp and Down Arrows LED Description Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Switch Type Configuring Network Options for Dial OperationCall Type Speech Data 64 kbps defaultAudio Data 56 kbps Terminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDN Front Panel Dial Options MenuRS-366 Sec or EON Wait for EON Sec or EON defaultSecurity 25 bis Enabled DisabledAuto Answer Dump all calls Call Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Port Mode Maintenance SetupAuto Traps Adlp Address Call NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE Options RS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Txinit Bonding Setup TXADD01 TxfaTxdeq Tanull Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Test Options Chapter TestingLoopback DTE Loopback Protocol Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Power Channel Switch CompatibilityChannel Aggregation Display Status Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Badinfoelem AccessinfodiscBearcapnotava Bonding + Capnotimplement CallrejectedChandoesnotexi Channotimpleme Facilitynotimp Dpump END RcvdFacilityrejected Facilitynotsub Incompatibledest IncomingcallbaIntrworking UNS Invalidcallref Network Busy MandatoryiemisNetworkcongesti Networkoutofo Servicenotavail ProtocolerrorNormalclearing Numberchanged Temporaryfailure TimerexpiryUnassignednumber Unspecifiedcause Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Commands should be entered without the AT prefix Appendix C AT CommandsAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands Appendix D Pinouts EIA-232 to DB-25 Adapter ConnectorRJ-45 Isdn Line Interface Table D-A EIA-232, RS-366, and RS-530 Connector Pinouts for IFC RJ-45 ConnectorsConnector Table D-B RS-366 Dialing Port Pinouts Table D-C RS-530 Pinouts Table D-DM e Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Presales Inquiries and Applications Support Product Support InformationPost-Sale Support Repair and Return