Channel Rate, Limited Distance Modem Application | ADTRAN ISU 512

Chapter 5: Configuration

		18,000 ft
		MIXED GAUGE WIRE
	LEASED	LEASED
DTE	MASTER	SLAVE	DTE
DTE			DTE

Figure 5-4

Limited Distance Modem Application

If two ISU 512 units are connected through channel banks, one unit should be configured for Slave mode and the other for Slave (Master); see Figure 5-5. To easily configure ISU 512s for this application, one unit can be optioned using Quick Setup, Leased Slave and the other can be optioned using Quick Setup, Leased Slave(Master). For more information, see the section Quick Setup Con- figuration in this chapter.

	BIMUX DP	BIMUX DP
	or Equivalent	or Equivalent
		T1
	ISU 512	ISU 512
DTE	SLAVE	SLAVE	DTE
DTE	MASTER		DTE
	MASTER

Figure 5-5

Leased Application with Channel Banks

Channel Rate

In Leased Line operation, the channel rate for the ISU 512 can be configured for 56 kbps or 64 kbps. When 64 kbps is selected, bandwidth of 1x64 kbps to 8x64 kbps can be selected by setting the maximum bit rate. See Maximum Bit Rate in the section Setting DTE Options for more information.

40

ISU 512 User Manual

61202.086L1-1

Image 56

ADTRAN ISU 512 user manual Channel Rate, Limited Distance Modem Application, Leased Application with Channel Banks

Contents

ISU Trademark 021S5 RJ-49C 1202086L1 1202086L2 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Isdn Overview Product Overview ISU 512 Rear Panel Understanding Isdn and the ISU ISU 512 Interoperability Videoconferencing Recommended Operating Protocols ISU 512 Synchronous Rates Understanding Isdn and the ISU Following instructions only apply to North American switches Chapter Ordering Isdn Ordering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Software Update Set the COM port for 38400, 8, 1, n and no flow control VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Menu Structure Main MenuLCD Display of the Main Menu Status Menu Basic Menu Traversal Front Panel ISU 512 Front View LCD Window Numeric KeypadUp and Down Arrows LED Description Operation Chapter Configuration Using Isdn Basic Rate Switched Service Configuration Menu Configuration Call Type Configuring Network Options for Dial OperationSwitch Type Data 64 kbps default SpeechAudio Data 56 kbps Outside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Setting the LDN Dial Options Dial Options Menu Front PanelRS-366 Sec or EON Sec or EON default Wait for EONSecurity 25 bis Disabled EnabledAuto Answer Dump all calls Select Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Maintenance Setup Port ModeAuto Traps Adlp Address Call NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Setting DTE Options Maximum Bit Rate RS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Bonding Setup Txinit Txfa TXADD01Txdeq Tanull Tcid Call Stagger Transparent 2 X Clear Channel Protocol Quick Setup Configuration Dial 512K Dial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Chapter Testing Test OptionsLoopback DTE Loopback Protocol Checker Near-End Block Errors/Far-End Block Errors NEBE/FEBE Software Version Testing If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID1,3,5, or If the Display Reads SPID2,4,6, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Chapter Specifications Summary Specifications and Features Channel Switch Compatibility PowerChannel Aggregation Display NET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Accessinfodisc BadinfoelemBearcapnotava Bonding + Callrejected CapnotimplementChandoesnotexi Channotimpleme Dpump END Rcvd FacilitynotimpFacilityrejected Facilitynotsub Incomingcallba IncompatibledestIntrworking UNS Invalidcallref Mandatoryiemis Network BusyNetworkcongesti Networkoutofo Protocolerror ServicenotavailNormalclearing Numberchanged Timerexpiry TemporaryfailureUnassignednumber Unspecifiedcause Wrongmsgforst Set Primary =Enable ISU 512 answers all calls default Appendix B Register List =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Appendix C AT Commands Commands should be entered without the AT prefixAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands EIA-232 to DB-25 Adapter Connector Appendix D PinoutsRJ-45 Isdn Line Interface Table D-A Pinouts for IFC RJ-45 Connectors EIA-232, RS-366, and RS-530 ConnectorConnector Table D-B Table D-C RS-366 Dialing Port Pinouts M e Table D-DRS-530 Pinouts Table D-E Pinouts Table D-F RS-530-to-V.35 Adapter Cable Pinouts Figure D-5 Figure D-6 Appendix D. Pinouts Acronyms Acronyms Glossary 2B1Q Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Index Numerics Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Product Support Information Presales Inquiries and Applications SupportPost-Sale Support Repair and Return