Chapter Specifications Summary | ADTRAN ISU 512 specs

Chapter 8

Specifications Summary

SPECIFICATIONS AND FEATURES

This section describes the standard specifications and features incorporated in the ISU 512.

Network Interface

Four RJ-45s for ISDN Basic Rate Interface

DTE Interface

RS-530 or V.35 (both connectors present)

Dialing Selections

•Manual or automatic stored number dialing, DTR assertion

•V.25 bis in-band DTE dialing

•RS-366 dial interface

•VT 100 menu interface

Data Rates

•Network: up to four BRIs (maximum of eight 56/64 kbps B channels)

•DTE: 56 kbps to 512 kbps synchronous

Rate Adaption

•BONDING mode 1

•2 x Clear Channel, dual port Clear Channel

Interoperability

•BONDING inverse multiplexers

•Switched 56 DSUs

•ISDN TAs

61202.086L1-1

ISU 512 User Manual

67

Image 83

ADTRAN ISU 512 user manual Chapter Specifications Summary, Specifications and Features

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Status Menu Menu StructureMain Menu LCD Display of the Main Menu Basic Menu Traversal ISU 512 Front View Front Panel LED Description LCD WindowNumeric Keypad Up and Down Arrows Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Call Type Configuring Network Options for Dial OperationSwitch Type Data 56 kbps Data 64 kbps defaultSpeech Audio Outside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Dial Options Setting the LDN Sec or EON Dial Options MenuFront Panel RS-366 25 bis Sec or EON defaultWait for EON Security Dump all calls DisabledEnabled Auto Answer Select Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Adlp Address Maintenance SetupPort Mode Auto Traps Call NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Maximum Bit Rate Setting DTE Options RS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Txinit Bonding Setup Tanull TxfaTXADD01 Txdeq Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Loopback Protocol Chapter TestingTest Options Loopback DTE Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Display Channel Switch CompatibilityPower Channel Aggregation NET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Bonding + AccessinfodiscBadinfoelem Bearcapnotava Channotimpleme CallrejectedCapnotimplement Chandoesnotexi Facilitynotsub Dpump END RcvdFacilitynotimp Facilityrejected Invalidcallref IncomingcallbaIncompatibledest Intrworking UNS Networkoutofo MandatoryiemisNetwork Busy Networkcongesti Numberchanged ProtocolerrorServicenotavail Normalclearing Unspecifiedcause TimerexpiryTemporaryfailure Unassignednumber Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Table C-A Appendix C AT CommandsCommands should be entered without the AT prefix AT Commands Appendix C. AT Commands 5ESS Appendix C. AT Commands Table D-A EIA-232 to DB-25 Adapter ConnectorAppendix D Pinouts RJ-45 Isdn Line Interface Table D-B Pinouts for IFC RJ-45 ConnectorsEIA-232, RS-366, and RS-530 Connector Connector RS-366 Dialing Port Pinouts Table D-C M e Table D-DRS-530 Pinouts Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Repair and Return Product Support InformationPresales Inquiries and Applications Support Post-Sale Support