Temporaryfailure, Timerexpiry, Unassignednumber | ADTRAN ISU 512

Appendix A. Status Buffer Messages

TANULL expired

Bonding timer TANULL expired; non BONDING equipment attempted to call into the ISU 512 while optioned for BONDING.

TEMPORARY_FAILURE

The network has temporarily failed; try the call again.

TIMER_EXPIRY

Call control error.

TXADD01 expired

Bonding timer TXADD01 expired, probably making a long distance call to a foreign country; adjust timer value to correct.

TXFA1 expired

Bonding timer TXFA1 expired; other vendor's BONDING equipment did not operate properly.

TXFA2 expired

Bonding timer TXFA1 expired; other vendor's BONDING equipment did not operate properly.

TXINIT expired

Bonding timer TXINIT expired; called non-BONDING equipment.

UNASSIGNED_NUMBER

The phone number dialed does not exist.

Unknown AT & cmd

User issued an unknown AT command.

UNSPECIFIED_CAUSE

Received a cause message from the network that is not understood.

USER_BUSY

The dialed number is busy.

WRONG_MESSAGE

The ISU 512 received a message that does not match the valid messages de- fined for the switch.

61202.086L1-1

ISU 512 User Manual

77

Image 93

ADTRAN ISU 512 user manual Temporaryfailure, Timerexpiry, Unassignednumber, Unspecifiedcause, Userbusy, Wrongmessage

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Chapter Installation InstallationNetwork Connection DTE Data Connection Dial Interface ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Chapter Operation Initial Self TestNetwork Connection Status Main Menu Menu StructureLCD Display of the Main Menu Status Menu Basic Menu Traversal ISU 512 Front View Front Panel Numeric Keypad LCD WindowUp and Down Arrows LED Description Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Configuring Network Options for Dial Operation Switch TypeCall Type Speech Data 64 kbps defaultAudio Data 56 kbps Setting the Spid Terminal IdentificationOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDN Front Panel Dial Options MenuRS-366 Sec or EON Wait for EON Sec or EON defaultSecurity 25 bis Enabled DisabledAuto Answer Dump all calls Connect Timeout Call ScreeningSelect Ansr if SN0. . .9 under Call Screening Remote Access Call Screening againRemote Download RDL Remote Supervision Port Mode Maintenance SetupAuto Traps Adlp Address Call NumID Configuring the ISU 512 for Leased Digital Service Clock ModeLeased Line Menu Channel Rate Limited Distance Modem ApplicationLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE Options Connector Type RS-530 to V.35 CableRS-366 Y Cable CTS Options CD OptionsDTR Options DSR Options Txinit Bonding Setup TXADD01 TxfaTxdeq Tanull Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 384K Dial 448KDial 336K Video 384K Video 336KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Test Options Chapter TestingLoopback DTE Loopback Protocol Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing Chapter Troubleshooting If Self Test FailsIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Power Channel Switch CompatibilityChannel Aggregation Display Appendix a Status Buffer Messages Status Line MessagesNET REM Loopback Ringing Badinfoelem AccessinfodiscBearcapnotava Bonding + Capnotimplement CallrejectedChandoesnotexi Channotimpleme Facilitynotimp Dpump END RcvdFacilityrejected Facilitynotsub Incompatibledest IncomingcallbaIntrworking UNS Invalidcallref Network Busy MandatoryiemisNetworkcongesti Networkoutofo Servicenotavail ProtocolerrorNormalclearing Numberchanged Temporaryfailure TimerexpiryUnassignednumber Unspecifiedcause Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Commands should be entered without the AT prefix Appendix C AT CommandsAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands Appendix D Pinouts EIA-232 to DB-25 Adapter ConnectorRJ-45 Isdn Line Interface Table D-A EIA-232, RS-366, and RS-530 Connector Pinouts for IFC RJ-45 ConnectorsConnector Table D-B RS-366 Dialing Port Pinouts Table D-C Table D-D RS-530 PinoutsM e Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Presales Inquiries and Applications Support Product Support InformationPost-Sale Support Repair and Return