Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN ISU 512 user manual Dial 384K, Dial 448K, Dial 336K

Models: ISU 512

1 129

Download 129 pages 36.74 Kb

Page 67

Chapter 5: Configuration

Dial 384K

When the ISU 512 is configured for Dial 384K service the following parame- ters are automatically preset:

Service type	ISDN dial line
Automatic answering	Enabled
ISDN call type	64 kbps data
Dial options	Front panel
Maximum bit rate	384 kbps
DTR options	Ignore
RS-530-V35 cable	Disabled
RS-366-Y cable	Disabled

Dial 448K

When the ISU 512 is configured for Dial 448K service the following parame- ters are automatically preset:

Service type	ISDN dial line
Automatic answering	Enabled
ISDN call type	56 kbps data
Dial options	Front panel
Maximum bit rate	448 kbps
DTR options	Ignore
RS-530-V35 cable	Disabled
RS-366-Y cable	Disabled

Dial 336K

When the ISU 512 is configured for Dial 336K service the following parame- ters are automatically preset:

Service type	ISDN dial line
Automatic answering	Enabled
ISDN call type	56 kbps data
Dial Options	Front panel

61202.086L1-1

ISU 512 User Manual

51

Image 67

ADTRAN ISU 512 user manual Dial 384K, Dial 448K, Dial 336K

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn OverviewISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 InteroperabilityISU 512 Synchronous Rates Recommended Operating ProtocolsUnderstanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switchesOrdering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software UpdateVT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status Status Menu Menu StructureMain Menu LCD Display of the Main MenuBasic Menu Traversal ISU 512 Front View Front PanelLED Description LCD WindowNumeric Keypad Up and Down ArrowsOperation Using Isdn Basic Rate Switched Service Chapter ConfigurationConfiguration Configuration MenuSwitch Type Configuring Network Options for Dial OperationCall Type Data 56 kbps Data 64 kbps defaultSpeech AudioTerminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDNSec or EON Dial Options MenuFront Panel RS-36625 bis Sec or EON defaultWait for EON SecurityDump all calls DisabledEnabled Auto AnswerCall Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Adlp Address Maintenance SetupPort Mode Auto TrapsCall NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE OptionsRS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Txinit Bonding SetupTanull TxfaTXADD01 TxdeqCall Stagger TcidTransparent 2 X Clear Channel Protocol Dial 512K Quick Setup ConfigurationDial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Loopback Protocol Chapter TestingTest Options Loopback DTEChecker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBETesting If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, orCONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications SummaryDisplay Channel Switch CompatibilityPower Channel AggregationStatus Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Bonding + AccessinfodiscBadinfoelem BearcapnotavaChannotimpleme CallrejectedCapnotimplement ChandoesnotexiFacilitynotsub Dpump END RcvdFacilitynotimp FacilityrejectedInvalidcallref IncomingcallbaIncompatibledest Intrworking UNSNetworkoutofo MandatoryiemisNetwork Busy NetworkcongestiNumberchanged ProtocolerrorServicenotavail NormalclearingUnspecifiedcause TimerexpiryTemporaryfailure UnassignednumberSet Primary WrongmsgforstAppendix B Register List =Enable ISU 512 answers all calls default=Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Table C-A Appendix C AT CommandsCommands should be entered without the AT prefix AT CommandsAppendix C. AT Commands 5ESS Appendix C. AT Commands Table D-A EIA-232 to DB-25 Adapter ConnectorAppendix D Pinouts RJ-45 Isdn Line InterfaceTable D-B Pinouts for IFC RJ-45 ConnectorsEIA-232, RS-366, and RS-530 Connector ConnectorRS-366 Dialing Port Pinouts Table D-CRS-530 Pinouts Table D-DM e Pinouts Table D-ERS-530-to-V.35 Adapter Cable Pinouts Table D-FFigure D-6 Figure D-5Appendix D. Pinouts Acronyms Acronyms 2B1Q GlossaryCcitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics IndexIndex Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Repair and Return Product Support InformationPresales Inquiries and Applications Support Post-Sale Support