Speech, Audio, Data 56 kbps, Data 64 kbps default | ADTRAN ISU 512

Chapter 5: Configuration

Speech

Speech directs the call control software to request a Mu-law/A-law speech cir- cuit as the bearer capability for outgoing calls. The Speech option is used with an ISDN line configured for voice service. In some areas voice service costs less than data service. A Speech call type does not guarantee an end-to-end digital connection with some local and long distance carriers.

Audio

Audio directs the call control software to request a 3.1 kHz audio circuit as the bearer capability for outgoing calls. The Audio option is used with an ISDN line configured for voice service. In some areas audio service is less expensive than data service. Selecting an Audio call type guarantees a digital end-to-end ISDN connection.

Data 56 kbps

Data 56 kbps directs the call control software to request a 64 kbps data circuit that is rate-adapted to 56 kbps. Data 56 kbps is intended for use in circum- stances where interoperability with Switched 56 service is desired.

Data 64 kbps (default)

The default Call type for ISDN service is Data 64 kbps. This directs the call control software to request an unrestricted 64 kbps circuit.

28

ISU 512 User Manual

61202.086L1-1

Image 44

ADTRAN ISU 512 user manual Speech, Audio, Data 56 kbps, Data 64 kbps default

Contents

ISU Trademark 021S5 RJ-49C 1202086L1 1202086L2 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Isdn Overview Product Overview ISU 512 Rear Panel Understanding Isdn and the ISU ISU 512 Interoperability Videoconferencing Recommended Operating Protocols ISU 512 Synchronous Rates Understanding Isdn and the ISU Following instructions only apply to North American switches Chapter Ordering Isdn Ordering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Software Update Set the COM port for 38400, 8, 1, n and no flow control VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Menu Structure Main MenuLCD Display of the Main Menu Status Menu Basic Menu Traversal Front Panel ISU 512 Front View LCD Window Numeric KeypadUp and Down Arrows LED Description Operation Chapter Configuration Using Isdn Basic Rate Switched Service Configuration Menu Configuration Call Type Configuring Network Options for Dial OperationSwitch Type Data 64 kbps default SpeechAudio Data 56 kbps Outside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Setting the LDN Dial Options Dial Options Menu Front PanelRS-366 Sec or EON Sec or EON default Wait for EONSecurity 25 bis Disabled EnabledAuto Answer Dump all calls Select Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Maintenance Setup Port ModeAuto Traps Adlp Address Call NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Setting DTE Options Maximum Bit Rate RS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Bonding Setup Txinit Txfa TXADD01Txdeq Tanull Tcid Call Stagger Transparent 2 X Clear Channel Protocol Quick Setup Configuration Dial 512K Dial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Chapter Testing Test OptionsLoopback DTE Loopback Protocol Checker Near-End Block Errors/Far-End Block Errors NEBE/FEBE Software Version Testing If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID1,3,5, or If the Display Reads SPID2,4,6, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Chapter Specifications Summary Specifications and Features Channel Switch Compatibility PowerChannel Aggregation Display NET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Accessinfodisc BadinfoelemBearcapnotava Bonding + Callrejected CapnotimplementChandoesnotexi Channotimpleme Dpump END Rcvd FacilitynotimpFacilityrejected Facilitynotsub Incomingcallba IncompatibledestIntrworking UNS Invalidcallref Mandatoryiemis Network BusyNetworkcongesti Networkoutofo Protocolerror ServicenotavailNormalclearing Numberchanged Timerexpiry TemporaryfailureUnassignednumber Unspecifiedcause Wrongmsgforst Set Primary =Enable ISU 512 answers all calls default Appendix B Register List =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Appendix C AT Commands Commands should be entered without the AT prefixAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands EIA-232 to DB-25 Adapter Connector Appendix D PinoutsRJ-45 Isdn Line Interface Table D-A Pinouts for IFC RJ-45 Connectors EIA-232, RS-366, and RS-530 ConnectorConnector Table D-B Table D-C RS-366 Dialing Port Pinouts M e Table D-DRS-530 Pinouts Table D-E Pinouts Table D-F RS-530-to-V.35 Adapter Cable Pinouts Figure D-5 Figure D-6 Appendix D. Pinouts Acronyms Acronyms Glossary 2B1Q Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Index Numerics Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Product Support Information Presales Inquiries and Applications SupportPost-Sale Support Repair and Return