Dpump END Rcvd, Facilitynotimp, Facilityrejected | ADTRAN ISU 512

Appendix A. Status Buffer Messages

DPUMP END RCVD

Indication of a hang-up or disconnect occurring during BONDING. Does not indicate an ERROR condition has occurred.

DTE not set V25

The DTE equipment is not optioned for the same bit rate as the ISU 512 for V.25 bis dialing.

DTR not up

ISU 512 tried to place a call in a dialing mode that requires DTR to be in an ac- tive state but it is not.

Dump call

ISU 512 could not accept an incoming call because it was already involved in a call.

Dump{1,2,3,4,6,7,8}

An incoming call on either the first or second channel was discarded by the ISU. The calling number is displayed if available.

FACILITY_NOT_IMP

The network does not support the requested supplementary service.

FACILITY_REJECTED

A facility requested by the user cannot be provided by the network.

FACILITY_NOT_SUB

The channel type requested has not been subscribed by the user.

FBW Disconnect

BONDING negotiation failed due to a disconnect on a B-Channel.

Hangup1/2

The call on either the first or second channel was disconnected by the ISU. The far-end phone number is also displayed.

Hardware Rev. F

The ISU 512 has a Revision F network daughterboard.

Hardware Rev. H

The ISU 512 has a Revision H network daughterboard.

61202.086L1-1

ISU 512 User Manual

73

Image 89

ADTRAN ISU 512 user manual Dpump END Rcvd, Facilitynotimp, Facilityrejected, Facilitynotsub

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Main Menu Menu StructureLCD Display of the Main Menu Status Menu Basic Menu Traversal ISU 512 Front View Front Panel Numeric Keypad LCD WindowUp and Down Arrows LED Description Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Call Type Configuring Network Options for Dial OperationSwitch Type Speech Data 64 kbps defaultAudio Data 56 kbps Outside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Dial Options Setting the LDN Front Panel Dial Options MenuRS-366 Sec or EON Wait for EON Sec or EON defaultSecurity 25 bis Enabled DisabledAuto Answer Dump all calls Select Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Port Mode Maintenance SetupAuto Traps Adlp Address Call NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Maximum Bit Rate Setting DTE Options RS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Txinit Bonding Setup TXADD01 TxfaTxdeq Tanull Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Test Options Chapter TestingLoopback DTE Loopback Protocol Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Power Channel Switch CompatibilityChannel Aggregation Display NET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Badinfoelem AccessinfodiscBearcapnotava Bonding + Capnotimplement CallrejectedChandoesnotexi Channotimpleme Facilitynotimp Dpump END RcvdFacilityrejected Facilitynotsub Incompatibledest IncomingcallbaIntrworking UNS Invalidcallref Network Busy MandatoryiemisNetworkcongesti Networkoutofo Servicenotavail ProtocolerrorNormalclearing Numberchanged Temporaryfailure TimerexpiryUnassignednumber Unspecifiedcause Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Commands should be entered without the AT prefix Appendix C AT CommandsAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands Appendix D Pinouts EIA-232 to DB-25 Adapter ConnectorRJ-45 Isdn Line Interface Table D-A EIA-232, RS-366, and RS-530 Connector Pinouts for IFC RJ-45 ConnectorsConnector Table D-B RS-366 Dialing Port Pinouts Table D-C M e Table D-DRS-530 Pinouts Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Presales Inquiries and Applications Support Product Support InformationPost-Sale Support Repair and Return