Dialing Options | ADTRAN ISU 512 manual

Chapter 5: Configuration

DIALING OPTIONS

Selecting 4=DIAL or pressing the # (pound) from the top of the menu tree dis- plays the available dialing options. (See Figure 5-3.) Use the following menu path to set dialing options:

4=Dial

1=Hang up line 2=Dial number 3=Redial last # 4=Answer Call 5=Dial stored # 6=Store/Review #

Hang Up Line

Terminates current call.

Dial Number

Allows a number to be entered and dialed from the key pad. If an error is made while entering a number, press Cancel to erase and reenter the number. Press Cancel twice consecutively to exit without dialing a number. Press En- ter after entering a number to dial the number and save the dialed number as stored number 9 for redialing purposes.

Redial Last Number

Allows redial of the last number called or attempted. This number was saved as stored number 9 from the last attempted phone call.

Answer Call

Allows selective answer of incoming calls when the Auto Answer is config- ured for disable. Auto Answer is described in Auto Answer in this chapter.

Dial Stored Number

Allows the dialing of one of ten stored phone numbers. Upon entering this menu, the Up and Down arrows permit viewing and selection of a stored number. Press Enter to dial the number. A copy of that number is saved as stored number 9 (SN9) for redial purposes.

54

ISU 512 User Manual

61202.086L1-1

Image 70

ADTRAN ISU 512 user manual Dialing Options

Contents

ISU Trademark 021S5 RJ-49C 1202086L1 1202086L2 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Isdn Overview Product Overview ISU 512 Rear Panel Understanding Isdn and the ISU ISU 512 Interoperability Videoconferencing Recommended Operating Protocols ISU 512 Synchronous Rates Understanding Isdn and the ISU Following instructions only apply to North American switches Chapter Ordering Isdn Ordering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Software Update Set the COM port for 38400, 8, 1, n and no flow control VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status LCD Display of the Main Menu Menu StructureMain Menu Status Menu Basic Menu Traversal Front Panel ISU 512 Front View Up and Down Arrows LCD WindowNumeric Keypad LED Description Operation Chapter Configuration Using Isdn Basic Rate Switched Service Configuration Menu Configuration Switch Type Configuring Network Options for Dial OperationCall Type Audio Data 64 kbps defaultSpeech Data 56 kbps Terminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Setting the LDN Dial Options RS-366 Dial Options MenuFront Panel Sec or EON Security Sec or EON defaultWait for EON 25 bis Auto Answer DisabledEnabled Dump all calls Call Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Auto Traps Maintenance SetupPort Mode Adlp Address Call NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Setting DTE Options Maximum Bit Rate RS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Bonding Setup Txinit Txdeq TxfaTXADD01 Tanull Tcid Call Stagger Transparent 2 X Clear Channel Protocol Quick Setup Configuration Dial 512K Dial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Loopback DTE Chapter TestingTest Options Loopback Protocol Checker Near-End Block Errors/Far-End Block Errors NEBE/FEBE Software Version Testing If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID1,3,5, or If the Display Reads SPID2,4,6, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Chapter Specifications Summary Specifications and Features Channel Aggregation Channel Switch CompatibilityPower Display Status Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Bearcapnotava AccessinfodiscBadinfoelem Bonding + Chandoesnotexi CallrejectedCapnotimplement Channotimpleme Facilityrejected Dpump END RcvdFacilitynotimp Facilitynotsub Intrworking UNS IncomingcallbaIncompatibledest Invalidcallref Networkcongesti MandatoryiemisNetwork Busy Networkoutofo Normalclearing ProtocolerrorServicenotavail Numberchanged Unassignednumber TimerexpiryTemporaryfailure Unspecifiedcause Wrongmsgforst Set Primary =Enable ISU 512 answers all calls default Appendix B Register List =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List AT Commands Appendix C AT CommandsCommands should be entered without the AT prefix Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands RJ-45 Isdn Line Interface EIA-232 to DB-25 Adapter ConnectorAppendix D Pinouts Table D-A Connector Pinouts for IFC RJ-45 ConnectorsEIA-232, RS-366, and RS-530 Connector Table D-B Table D-C RS-366 Dialing Port Pinouts RS-530 Pinouts Table D-DM e Table D-E Pinouts Table D-F RS-530-to-V.35 Adapter Cable Pinouts Figure D-5 Figure D-6 Appendix D. Pinouts Acronyms Acronyms Glossary 2B1Q Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Index Numerics Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Post-Sale Support Product Support InformationPresales Inquiries and Applications Support Repair and Return