Mandatoryiemis, Network Busy, Networkcongesti | ADTRAN ISU 512

Appendix A. Status Buffer Messages

MANDATORY_IE_MIS

Mandatory information element missing.

Need 64K call

The BONDING protocol requires the ISU 512 to be configured for a 64k data call type.

Negotiation fail

The BONDING negotiation has failed.

NETWORK BUSY

The ISDN switch is busy and unable to process a call.

NETWORK_CONGESTI

The phone network is currently congested.

NETWORK_OUT_OF_O

The phone network is out of order.

NO_CIRCUIT_AVAIL

The requested bearer channel is not available.

NONEXISTENT_MSG

Nonexistent message was sent by the ISU.

No Sreg number

User attempted to access an S-register but did not specify an S-register (exam- ple: S=1).

No Sreg value

User attempted to change an S-register but did not specify a value (example: S2= ).

NO_ROUTE

The phone network was unable to find a route to the destination number.

NO 2x64/56

2 x Clear Channel mode failed. The RS-530 port is set to primary. This is an invalid configuration for using 2 x Clear Channel mode.

NO_USER_RESPONDI

The dialed number is not responding.

61202.086L1-1

ISU 512 User Manual

75

Image 91

ADTRAN ISU 512 Mandatoryiemis, Network Busy, Networkcongesti, Networkoutofo, Nocircuitavail, Nonexistentmsg, Noroute

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status Status Menu Menu StructureMain Menu LCD Display of the Main Menu Basic Menu Traversal ISU 512 Front View Front Panel LED Description LCD WindowNumeric Keypad Up and Down Arrows Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Switch Type Configuring Network Options for Dial OperationCall Type Data 56 kbps Data 64 kbps defaultSpeech Audio Terminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDN Sec or EON Dial Options MenuFront Panel RS-366 25 bis Sec or EON defaultWait for EON Security Dump all calls DisabledEnabled Auto Answer Call Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Adlp Address Maintenance SetupPort Mode Auto Traps Call NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE Options RS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Txinit Bonding Setup Tanull TxfaTXADD01 Txdeq Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Loopback Protocol Chapter TestingTest Options Loopback DTE Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Display Channel Switch CompatibilityPower Channel Aggregation Status Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Bonding + AccessinfodiscBadinfoelem Bearcapnotava Channotimpleme CallrejectedCapnotimplement Chandoesnotexi Facilitynotsub Dpump END RcvdFacilitynotimp Facilityrejected Invalidcallref IncomingcallbaIncompatibledest Intrworking UNS Networkoutofo MandatoryiemisNetwork Busy Networkcongesti Numberchanged ProtocolerrorServicenotavail Normalclearing Unspecifiedcause TimerexpiryTemporaryfailure Unassignednumber Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Table C-A Appendix C AT CommandsCommands should be entered without the AT prefix AT Commands Appendix C. AT Commands 5ESS Appendix C. AT Commands Table D-A EIA-232 to DB-25 Adapter ConnectorAppendix D Pinouts RJ-45 Isdn Line Interface Table D-B Pinouts for IFC RJ-45 ConnectorsEIA-232, RS-366, and RS-530 Connector Connector RS-366 Dialing Port Pinouts Table D-C RS-530 Pinouts Table D-DM e Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Repair and Return Product Support InformationPresales Inquiries and Applications Support Post-Sale Support