Chapter Installation, Network Connection | ADTRAN ISU 512 manual

Chapter 3

Installation

INSTALLATION

After unpacking the unit, immediately inspect it for possible shipping dam- age. If damage is discovered, file a claim immediately with the shipping car- rier, then contact ADTRAN Customer Service; see the inside back cover of this manual for phone numbers.

NETWORK CONNECTION

The ISU 512 (U interface) supports either Dial or Leased operation. The ISU 512 (ST interface) supports only Dial operation. Four 8-pin RJ-45 modular jacks on the rear panel of the ISU 512 allow connection to either network ser- vice.

Dial operation uses the ISDN Basic Rate interface and allows the ISU 512 to dial out over the ISDN network. When used in this mode of operation, the telephone company provided ISDN Basic Rate interface is connected to the RJ- 45 connectors marked ISDN IFC #1, #2, #3, and #4. Connect the Basic Rate in- terfaces to the ISU 512 in order, starting with ISDN IFC #1, until the maximum number of lines (four) is reached.

The Leased mode of operation supports a dedicated 2B1Q data service at rates of up to 512 kbps by using nailed up circuits or a permanent connection be- tween end points. This could be a limited distance modem or point-to-point connection.

See the appendix Pinouts for network connection pin assignments.

61202.086L1-1

ISU 512 User Manual

9

Image 25

ADTRAN ISU 512 user manual Chapter Installation, Network Connection

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status Main Menu Menu StructureLCD Display of the Main Menu Status Menu Basic Menu Traversal ISU 512 Front View Front Panel Numeric Keypad LCD WindowUp and Down Arrows LED Description Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Switch Type Configuring Network Options for Dial OperationCall Type Speech Data 64 kbps defaultAudio Data 56 kbps Terminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDN Front Panel Dial Options MenuRS-366 Sec or EON Wait for EON Sec or EON defaultSecurity 25 bis Enabled DisabledAuto Answer Dump all calls Call Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Port Mode Maintenance SetupAuto Traps Adlp Address Call NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE Options RS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Txinit Bonding Setup TXADD01 TxfaTxdeq Tanull Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Test Options Chapter TestingLoopback DTE Loopback Protocol Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Power Channel Switch CompatibilityChannel Aggregation Display Status Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Badinfoelem AccessinfodiscBearcapnotava Bonding + Capnotimplement CallrejectedChandoesnotexi Channotimpleme Facilitynotimp Dpump END RcvdFacilityrejected Facilitynotsub Incompatibledest IncomingcallbaIntrworking UNS Invalidcallref Network Busy MandatoryiemisNetworkcongesti Networkoutofo Servicenotavail ProtocolerrorNormalclearing Numberchanged Temporaryfailure TimerexpiryUnassignednumber Unspecifiedcause Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Commands should be entered without the AT prefix Appendix C AT CommandsAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands Appendix D Pinouts EIA-232 to DB-25 Adapter ConnectorRJ-45 Isdn Line Interface Table D-A EIA-232, RS-366, and RS-530 Connector Pinouts for IFC RJ-45 ConnectorsConnector Table D-B RS-366 Dialing Port Pinouts Table D-C RS-530 Pinouts Table D-DM e Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Presales Inquiries and Applications Support Product Support InformationPost-Sale Support Repair and Return