50=Wait for 5 seconds or EON default | ADTRAN ISU 512 specification

Appenidix B. S-Register List

S45 . . . . BOND TCID. . . . . . . . . . The number of seconds both end points attempt to negoti- ate agreeable values for bearer channels and channel ca- pacities before deciding the BONDING call has failed. 0 to 256, 5 sec is default.

S47 . . . . RS 366 TIME . . . . . . . . . Determines the amount of time the RS-366 port waits for either EON or inactivity to terminate a dial string before di- aling a number.

0=Wait for EON only 10=Wait for 1 second or EON 20=Wait for 2 seconds or EON

50=Wait for 5 seconds or EON (default)

100=Wait for 10 seconds or EON 200=Wait for 20 seconds or EON

S50 . . . . LINE MODE. . . . . . . . . . Selects the operating mode of the ISU 512.

0=Dial service (switched service) (default)

1=Leased service (non-switched service)

S51 . . . . LINE CLOCK. . . . . . . . . Selects the clock mode in leased mode.

0=Slave (default)

1=Master (leased line only, limited distance modem appli- cation only)

S52 . . . . SWITCH TYPE . . . . . . . Selects the network switch type for dial service.

0=AT&T 5ESS (default)

1=Northern Telecom DMS-100 2=National ISDN-1

3=NEC

4=EuroISDN (only available on the ISU 512 ST)

S53 . . . . CALL TYPE . . . . . . . . . . Call type. 0=Speech 1=Audio 2=56 kbps data

3=64 kbps data (default)

61202.086L1-1

ISU 512 User Manual

81

Image 97

ADTRAN ISU 512 user manual 50=Wait for 5 seconds or EON default

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1 Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn Overview ISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 Interoperability ISU 512 Synchronous Rates Recommended Operating Protocols Understanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switches Ordering Isdn Installation Chapter InstallationNetwork Connection Dial Interface Connection DTE Data ConnectionSmart Dial String Formats Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software Update VT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Initial Self Test Chapter OperationNetwork Connection Status Main Menu Menu StructureLCD Display of the Main Menu Status Menu Basic Menu Traversal ISU 512 Front View Front Panel Numeric Keypad LCD WindowUp and Down Arrows LED Description Operation Using Isdn Basic Rate Switched Service Chapter Configuration Configuration Configuration Menu Switch Type Configuring Network Options for Dial OperationCall Type Speech Data 64 kbps defaultAudio Data 56 kbps Terminal Identification Setting the SpidOutside of North America, SPIDs do not have to be entered Dial Options Setting the LDN Front Panel Dial Options MenuRS-366 Sec or EON Wait for EON Sec or EON defaultSecurity 25 bis Enabled DisabledAuto Answer Dump all calls Call Screening Connect TimeoutSelect Ansr if SN0. . .9 under Call Screening Call Screening again Remote AccessRemote Download RDL Remote Supervision Port Mode Maintenance SetupAuto Traps Adlp Address Call NumID Clock Mode Configuring the ISU 512 for Leased Digital ServiceLeased Line Menu Limited Distance Modem Application Channel RateLeased Application with Channel Banks Test Remote Maximum Bit Rate Setting DTE Options RS-530 to V.35 Cable Connector TypeRS-366 Y Cable CD Options CTS OptionsDTR Options DSR Options Txinit Bonding Setup TXADD01 TxfaTxdeq Tanull Call Stagger Tcid Transparent 2 X Clear Channel Protocol Dial 512K Quick Setup Configuration Dial 448K Dial 384KDial 336K Video 336K Video 384KLeased Master Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Test Options Chapter TestingLoopback DTE Loopback Protocol Checker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBE Testing If Self Test Fails Chapter TroubleshootingIf AN Isdn Network Line Reads Down Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, or CONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications Summary Power Channel Switch CompatibilityChannel Aggregation Display Status Line Messages Appendix a Status Buffer MessagesNET REM Loopback Ringing Badinfoelem AccessinfodiscBearcapnotava Bonding + Capnotimplement CallrejectedChandoesnotexi Channotimpleme Facilitynotimp Dpump END RcvdFacilityrejected Facilitynotsub Incompatibledest IncomingcallbaIntrworking UNS Invalidcallref Network Busy MandatoryiemisNetworkcongesti Networkoutofo Servicenotavail ProtocolerrorNormalclearing Numberchanged Temporaryfailure TimerexpiryUnassignednumber Unspecifiedcause Set Primary Wrongmsgforst Appendix B Register List =Enable ISU 512 answers all calls default =Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Commands should be entered without the AT prefix Appendix C AT CommandsAT Commands Table C-A Appendix C. AT Commands 5ESS Appendix C. AT Commands Appendix D Pinouts EIA-232 to DB-25 Adapter ConnectorRJ-45 Isdn Line Interface Table D-A EIA-232, RS-366, and RS-530 Connector Pinouts for IFC RJ-45 ConnectorsConnector Table D-B RS-366 Dialing Port Pinouts Table D-C RS-530 Pinouts Table D-DM e Pinouts Table D-E RS-530-to-V.35 Adapter Cable Pinouts Table D-F Figure D-6 Figure D-5 Appendix D. Pinouts Acronyms Acronyms 2B1Q Glossary Ccitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics Index Index Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Presales Inquiries and Applications Support Product Support InformationPost-Sale Support Repair and Return