Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN ISU 512 user manual Chapter Operation, Initial Self Test, Network Connection Status

Models: ISU 512

1 129

Download 129 pages 36.74 Kb

Page 35

Chapter 4

Operation

INITIAL SELF TEST

The ISU 512 performs an initial self test upon initial installation. Once the self test is successfully completed, the current status mode is displayed. If the ISU 512 is not connected to the network, the Status menu displays DOWN next to the network connection number. If the unit is connected to the network and functioning properly, READY is displayed next to the network connection number; see Figure 4-1. A list of current status messages is provided in the ap- pendix Status Buffer Messages.

Figure 4-1

Network Connection Status

To quickly and easily configure the ISU 512 for most common applications, see Quick Setup Configuration in the chapter Configuration.

61202.086L1-1

ISU 512 User Manual

19

Image 35

ADTRAN ISU 512 user manual Chapter Operation, Initial Self Test, Network Connection Status

Contents

ISU Trademark 021S5 RJ-49C 1202086L2 1202086L1Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Product Overview Isdn OverviewISU 512 Rear Panel Understanding Isdn and the ISU Videoconferencing ISU 512 InteroperabilityISU 512 Synchronous Rates Recommended Operating ProtocolsUnderstanding Isdn and the ISU Chapter Ordering Isdn Following instructions only apply to North American switchesOrdering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Set the COM port for 38400, 8, 1, n and no flow control Software UpdateVT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Status Menu Menu StructureMain Menu LCD Display of the Main MenuBasic Menu Traversal ISU 512 Front View Front PanelLED Description LCD WindowNumeric Keypad Up and Down ArrowsOperation Using Isdn Basic Rate Switched Service Chapter ConfigurationConfiguration Configuration MenuCall Type Configuring Network Options for Dial OperationSwitch Type Data 56 kbps Data 64 kbps defaultSpeech AudioOutside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Dial Options Setting the LDNSec or EON Dial Options MenuFront Panel RS-36625 bis Sec or EON defaultWait for EON SecurityDump all calls DisabledEnabled Auto AnswerSelect Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Adlp Address Maintenance SetupPort Mode Auto TrapsCall NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Maximum Bit Rate Setting DTE OptionsRS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Txinit Bonding SetupTanull TxfaTXADD01 TxdeqCall Stagger TcidTransparent 2 X Clear Channel Protocol Dial 512K Quick Setup ConfigurationDial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Loopback Protocol Chapter TestingTest Options Loopback DTEChecker Software Version Near-End Block Errors/Far-End Block Errors NEBE/FEBETesting If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID2,4,6, or If the Display Reads SPID1,3,5, orCONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Specifications and Features Chapter Specifications SummaryDisplay Channel Switch CompatibilityPower Channel AggregationNET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Bonding + AccessinfodiscBadinfoelem BearcapnotavaChannotimpleme CallrejectedCapnotimplement ChandoesnotexiFacilitynotsub Dpump END RcvdFacilitynotimp FacilityrejectedInvalidcallref IncomingcallbaIncompatibledest Intrworking UNSNetworkoutofo MandatoryiemisNetwork Busy NetworkcongestiNumberchanged ProtocolerrorServicenotavail NormalclearingUnspecifiedcause TimerexpiryTemporaryfailure UnassignednumberSet Primary WrongmsgforstAppendix B Register List =Enable ISU 512 answers all calls default=Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Table C-A Appendix C AT CommandsCommands should be entered without the AT prefix AT CommandsAppendix C. AT Commands 5ESS Appendix C. AT Commands Table D-A EIA-232 to DB-25 Adapter ConnectorAppendix D Pinouts RJ-45 Isdn Line InterfaceTable D-B Pinouts for IFC RJ-45 ConnectorsEIA-232, RS-366, and RS-530 Connector ConnectorRS-366 Dialing Port Pinouts Table D-CM e Table D-DRS-530 Pinouts Pinouts Table D-ERS-530-to-V.35 Adapter Cable Pinouts Table D-FFigure D-6 Figure D-5Appendix D. Pinouts Acronyms Acronyms 2B1Q GlossaryCcitt DDS Isdn NT1 Interface S reference point Xmodem 106 Numerics IndexIndex Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Repair and Return Product Support InformationPresales Inquiries and Applications Support Post-Sale Support