Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN ISU 512 Normalclearing, Numberchanged, Outgoingcallba, Pre-Empted, Protocolerror

Models: ISU 512

1 129

Download 129 pages 36.74 Kb

Page 92

Appendix A. Status Buffer Messages

NORMAL_CLEARING

The network is disconnecting the current call.

NOT end2end ISDN

The path that the call was routed over is not ISDN from end-to-end (warning only).

NUMBER_CHANGED

The number dialed has been changed.

OUTGOING_CALL_BA

The network will not allow the outgoing call to be placed.

PRE-EMPTED

The network pre-empted the call.

PROTOCOL_ERROR

Call control error.

REQ_CHANNEL_NOT_

The channel type requested is currently not available.

Remote not ISU

Bonding negotiation determined the far-end unit is not another ISU 512.

RESP_TO_STAT_ENQ

Response to status enquiry.

Ring 1/2

An incoming call on either the first or second channel entered the Ring state. The calling phone number is displayed if available.

S cmd not = or ?

User did not use proper syntax in the command string.

SERVICE_NOT_AVAIL

The service requested by the user is not available.

SOURCE NOT ISDN

The incoming calling party is not ISDN (warning only).

SReg SetError

Local DTE invalid S-register setting.

76

ISU 512 User Manual

61202.086L1-1

Image 92

ADTRAN ISU 512 Normalclearing, Numberchanged, Outgoingcallba, Pre-Empted, Protocolerror, Reqchannelnot, Resptostatenq

Contents

ISU Trademark 021S5 RJ-49C 1202086L1 1202086L2Canadian Emissions Requirements Canadian Equipment Limitations Quick Start Guide SPID1/LDN1 Table of Contents Table of Contents Txinit Txfa TXADD01 Txdeq Tanull Tcid 107 List of Figures Table of Contents List of Tables Viii Isdn Overview Product OverviewISU 512 Rear Panel Understanding Isdn and the ISU ISU 512 Interoperability VideoconferencingRecommended Operating Protocols ISU 512 Synchronous RatesUnderstanding Isdn and the ISU Following instructions only apply to North American switches Chapter Ordering IsdnOrdering Isdn Network Connection Chapter InstallationInstallation Smart Dial String Formats DTE Data ConnectionDial Interface Connection Installation Maintenance Interface Software Update Set the COM port for 38400, 8, 1, n and no flow controlVT 100 Menu Interface VT 100 Configuration Menu VT 100 Status Screen VT 100 Test Menu VT 100 Dial Menu Installation Network Connection Status Chapter OperationInitial Self Test Menu Structure Main MenuLCD Display of the Main Menu Status MenuBasic Menu Traversal Front Panel ISU 512 Front ViewLCD Window Numeric KeypadUp and Down Arrows LED DescriptionOperation Chapter Configuration Using Isdn Basic Rate Switched ServiceConfiguration Menu ConfigurationCall Type Configuring Network Options for Dial OperationSwitch Type Data 64 kbps default SpeechAudio Data 56 kbpsOutside of North America, SPIDs do not have to be entered Setting the SpidTerminal Identification Setting the LDN Dial OptionsDial Options Menu Front PanelRS-366 Sec or EONSec or EON default Wait for EONSecurity 25 bisDisabled EnabledAuto Answer Dump all callsSelect Ansr if SN0. . .9 under Call Screening Connect TimeoutCall Screening Remote Download RDL Remote AccessCall Screening again Remote Supervision Maintenance Setup Port ModeAuto Traps Adlp AddressCall NumID Leased Line Menu Configuring the ISU 512 for Leased Digital ServiceClock Mode Leased Application with Channel Banks Channel RateLimited Distance Modem Application Test Remote Setting DTE Options Maximum Bit RateRS-366 Y Cable Connector TypeRS-530 to V.35 Cable DTR Options CTS OptionsCD Options DSR Options Bonding Setup TxinitTxfa TXADD01Txdeq TanullTcid Call StaggerTransparent 2 X Clear Channel Protocol Quick Setup Configuration Dial 512KDial 336K Dial 384KDial 448K Leased Master Video 384KVideo 336K Leased Slave and Ldm SlvMstr Dialing Options Store/Review Number Configuring the ISU 512 for V.25 BIS IN-BAND Dialing Chapter Testing Test OptionsLoopback DTE Loopback ProtocolChecker Near-End Block Errors/Far-End Block Errors NEBE/FEBE Software VersionTesting If AN Isdn Network Line Reads Down Chapter TroubleshootingIf Self Test Fails Troubleshooting If the Display Reads TEI1 If the Display Reads TEI2 If the Display Reads SPID1,3,5, or If the Display Reads SPID2,4,6, orCONFIG, Netw. options, Dial Line, Terminal ID, and SPID/LDN Chapter Specifications Summary Specifications and FeaturesChannel Switch Compatibility PowerChannel Aggregation DisplayNET REM Loopback Appendix a Status Buffer MessagesStatus Line Messages Ringing Accessinfodisc BadinfoelemBearcapnotava Bonding +Callrejected CapnotimplementChandoesnotexi ChannotimplemeDpump END Rcvd FacilitynotimpFacilityrejected FacilitynotsubIncomingcallba IncompatibledestIntrworking UNS InvalidcallrefMandatoryiemis Network BusyNetworkcongesti NetworkoutofoProtocolerror ServicenotavailNormalclearing NumberchangedTimerexpiry TemporaryfailureUnassignednumber UnspecifiedcauseWrongmsgforst Set Primary=Enable ISU 512 answers all calls default Appendix B Register List=Ignore DTR default 50=Wait for 5 seconds or EON default =Disable default Appenidix B. S-Register List Appenidix B. S-Register List Appendix C AT Commands Commands should be entered without the AT prefixAT Commands Table C-AAppendix C. AT Commands 5ESS Appendix C. AT Commands EIA-232 to DB-25 Adapter Connector Appendix D PinoutsRJ-45 Isdn Line Interface Table D-APinouts for IFC RJ-45 Connectors EIA-232, RS-366, and RS-530 ConnectorConnector Table D-BTable D-C RS-366 Dialing Port PinoutsM e Table D-DRS-530 Pinouts Table D-E PinoutsTable D-F RS-530-to-V.35 Adapter Cable PinoutsFigure D-5 Figure D-6Appendix D. Pinouts Acronyms Acronyms Glossary 2B1QCcitt DDS Isdn NT1 Interface S reference point Xmodem 106 Index NumericsIndex Isdn 110 TXADD01 47 Txdeq 47 Txfa 47 Txinit 112 Product Support Information Presales Inquiries and Applications SupportPost-Sale Support Repair and Return